156997240en.qxp 12/27/2006 1:39 PM Page 1 User manual Dishwasher ZDT 110 156997240en.qxp 12/27/2006 1:39 PM Page 2 Content Safety information - - - - - - - - - - - - - - - - - - -3 Control panel and functions - - - - - - - - - - - -4 Audible signals - - - - - - - - - - - - - - - - - - - - -6 Programme table - - - - - - - - - - - - - - - - - - -7 Before the first use - - - - - - - - - - - - - - - - - -8 Setting the water softener - - - - - - - - - - - - -8 Filling with dishwasher salt - - - - - - - - - - - -11 Filling with rinse aid - - - - - - - - - - - - - - - - -12 Adjusting the dosage of rinse aid - - - - - - -12 Loading cutlery and dishes - - - - - - - - - - -13 Filling with detergent - - - - - - - - - - - - - - - -15 Unloading the dishwasher - - - - - - - - - - - -15 Cleaning and care- - - - - - - - - - - - - - - - - - 16 Environmental concerns - - - - - - - - - - - - - 17 Something not working - - - - - - - - - - - - - - 18 Technical data- - - - - - - - - - - - - - - - - - - - - 20 Consumption values - - - - - - - - - - - - - - - - 20 Hints for Test Institutes - - - - - - - - - - - - - - 21 Installation - - - - - - - - - - - - - - - - - - - - - - - 22 Guarantee/Customer Service - - - - - - - - - - 25 European guarantee - - - - - - - - - - - - - - - - 27 2 156997240en.qxp 12/27/2006 1:39 PM Page 3 Safety information In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features. Save these instructions and make sure that they remain with the appliance if it is moved or sold, so that everyone using it through its life will be properly informed on appliance use and safety. Correct use This dishwasher is only intended for washing household utensils suitable for machine washing. Do not put any solvents in the dishwasher. This could cause an explosion. Knives and other items with sharp points must be loaded in the cutlery basket with their points down or placed in a horizontal position in the upper basket. Only use products (detergent, salt and rinse aid) suitable for dishwashers. Avoid opening the door whilst the appliance is in operation, hot steam may escape. Do not take any dishes out of the dishwasher before the end of the dishwashing cycle. After use, isolate the appliance from the power supply and turn off the water supply. This product should be serviced only by an authorised service engineer, and only genuine spare parts should be used. Ensure that the door of the dishwasher is always closed when it is not being loaded or unloaded. In this way you will avoid anybody tripping over the open door and hurting themselves. Do not sit or stand on the open door. Child safety This appliance is designed to be operated by adults. Don't allow children to use the dishwasher unsupervised. Keep all packaging well away from children. There is risk of suffocation. Keep all detergents in a safe place out of children's reach. Keep children well away from the dishwasher when the door is open. Installation General safety Check your dishwasher for any transport damage. Never connect a damaged machine. If your dishwasher is damaged contact your supplier. All packaging must be removed before use. Any electrical and plumbing work required to install this appliance must be carried out by a qualified and competent person. For safety reasons it is dangerous to alter the specifications or attempt to modify this product in any way. 3 Dishwasher detergents can cause chemical burns to eyes, mouth and throat. Could endanger life! Comply with the safety instructions of the dishwasher detergent manufacturer. The water in your dishwasher is not for drinking. Detergent residues may still be present in your machine. 156997240en.qxp 12/27/2006 1:39 PM Page 4 Never use the dishwasher if the electrical supply cable and water hoses are damaged; or if the control panel, work top or plinth area are damaged such that the inside of the appliance is freely accessible. Contact your local Service Force centre, in order to avoid hazard. All sides of the dishwasher must never be drilled to prevent damage to hydraulic and electric components. WARNING! For electrical and water connection carefully follow the instructions given in specific paragraphs. Control panel and functions In this fully integrated appliance the controls are located on the top of the door. When selecting a washing programme, the door needs to be slightly open. 1. On-Off button 2. Programme/Cancel button 3. End of cycle light 4. Programme lights IMPORTANT! Always remember that when performing operations such as: - selecting a washing programme, - deactivation/activation of the audible signals, - setting the water softener, the appliance MUST be in setting mode: Press On-Off button, all programme lights are illuminated and End of cycle light flashes = appliance in setting mode. Press On-Off button, a programme light is illuminated and End of cycle light is illuminated with fixed light = last performed programme still set. In this case the programme has to be cancelled (see instructions "Cancel a washing programme in progress"). 4 156997240en.qxp 12/27/2006 1:39 PM Page 5 Programme/Cancel 1. Press the On-Off button. button Starting the washing programme: 2. Press the Programme/Cancel once, the light of the last performed washing programme illuminates and the End of cycle light flashes. 3. Press the Programme/Cancel as many times as necessary to illuminate the light corresponding to the desired programme. 4. Close the dishwasher's door, the programme will start automatically. IMPORTANT! Once the programme has started, if you want to change the selection made you must cancel the washing programme in progress. Cancel the washing programme in progress: 1. Open the door. 2. Press and hold the Programme/Cancel button until the light of the running programme turns off and the End of cycle light is flashing. 3. Release the Programme/Cancel button. 4. Switch off the machine by pressing the On-Off button or select a new washing programme (check that there is detergent in the detergent dispenser. Illuminates when a washing programme has ended. Switch of the dishwasher by returning the programme selector dial to the Off position. The On/Off indicator light turns off. It also has added functions of visual signalling as: - the setting of the water softener, - intervention of an alarm due to the malfunction of the machine. - deactivation/activation of the audible signals. End of cycle Audible signals Audible signals have been introduced to help indicate which operations the dishwasher is performing. - end of the washing programme, - malfunction of the appliance. Factory setting: audible signals activated. 5 156997240en.qxp 12/27/2006 1:39 PM Page 6 Deactivation/activation of the audible signals 1. The dishwasher must be switched off. Switch on the dishwasher by pressing the On-Off button. 2. Press and hold Programme/Cancel button until programme light A flashes and programme light B illuminates with fixed light. 3. Press Programme/Cancel button again: programme light A becomes fixed and programme light B starts flashing. 4. After a few seconds programme light A turns off, programme light B goes on flashing and End of cycle light illuminates with fixed light. The illumination of the End of cycle light means that the audible signals are active. 5. To deactivate the audible signals, press the Programme/-Cancel button, the End of cycle light turns off indicating that the audible signals have been deactivated. 6. To memorise the operation, switch off the dishwasher by pressing the On-Off button. 7. To reactivate again the audible signals, follow the instructions till point 4. Wait a few seconds and then press the Programme/Cancel button, the End of cycle light illuminates indicating that the audible signals have been reactivated. 6 156997240en.qxp 12/27/2006 1:39 PM Page 7 Programme table Programme 65° NORMAL Use Normal soil Crockery and cutlery Cycle description Prewash Main wash 2 intermediate rinses Final rinse Dry Main wash Final rinse Light soil Crockery and cutlery Normal soil Crockery and cutlery Prewash Main wash 1 intermediate rinse Final rinse Dry Prewash RINSE & HOLD Any Partial load (to be completed later in theday). This programme does not require the use of detergent. 7 156997240en.qxp 12/27/2006 1:39 PM Page 8 Before the first use When using separate special (dishwasher) salt, rinse aid and detergent: - set the water softener - add special salt - fill up with rinse aid IMPORTANT! If the drying results are not satisfactory we recommend that you: 1. Fill up the rinse aid dispenser with rinse aid. 2. Set the rinse aid dosage to position 2. If you decide in future to use separated detergents, we advise that you: - Fill up the salt and rinse aid container. - Adjust the water hardness setting to the highest level and perform 1 normal washing programme without loading any dishes. - Adjust the water hardness setting according to the hardness of the water in your area. - Adjust the rinse aid dosage When using tablets that integrate rinse aid and detergent: there is no need to fill up with rinse aid - set the water softener - add special (dishwasher) salt When using tablets that integrate rinse aid, detergent, salt function and other additives: there is no need to fill up with special salt or rinse aid. Check whether these detergents are suitable for your water hardness. Follow the manufacturers instructions. - Set the water hardness to level 1. Setting the water softener The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply, which would have a detrimental or adverse effect on the operation of the appliance. The softener should be adjusted according to the hardness of the water in your area. Your local Water Authority can advise you on the hardness of the water in your area. 8 IMPORTANT! The water softener must be set in both ways: manually and electronically. 156997240en.qxp 12/27/2006 1:39 PM Page 9 Water hardness in Clarke1) 64 - 88 53 - 63 46 - 52 36 - 45 28 - 35 23 - 27 18 - 22 13 - 17 5 - 12 <5 in °TH2) 91 - 125 76 - 90 65 - 75 51 - 64 40 - 50 33 - 39 26 - 32 19 - 25 7 - 18 <7 in mmol/l3) 9,0 - 12,5 7,6 - 8,9 6,5 - 7,5 5,1 - 6,4 4,0 - 5,0 3,3 - 3,9 2,6 - 3,2 1,9 - 2,5 0,7 - 1,8 < 0,7 Number of flashes of the "end of programme" light Adjustment of the water hardness setting manually electronically level 10 level 9 level 8 level 7 level 6 level 5 level 4 level 3 level 2 level 1 no salt necessary factory setting 10 9 8 7 6 5 4 3 2 1 2 2 2 2 2 2 1 1 1 1 1) Clarke degree, measure of the water hardness. 2) (°TH) French degree, measure of the water hardness. 3) (mmol/l) millimol per litre, international unit for water hardness Setting the water softener manually (see table) The water softener is factory set at position 2. Set switch to position 1 or 2 9 156997240en.qxp 12/27/2006 1:39 PM Page 10 Setting the water softener electronically (see table) The water softener is factory set at position 5. 1. The dishwasher must be switched off. Switch on the dishwasher by pressing the On-Off button. 2. Press and hold Programme/Cancel button until programme light A flashes and programme light B illuminates with fixed light. 3. Wait until programme light B turns off, programme light A goes on flashing and simultaneously End of cycle light starts flashing. The number of flashes of the End of cycle light corresponds to current level set. The End of cycle light might flash 5 times, for example. The flashing is repeated every 5 seconds. 4. To change the level, press the Programme/Cancel button. Each time the button is pressed the level increases. (Level 1 follows level 10). The End of cycle light indicates the new setting. 5. TTo memorise the operation, switch off the dishwasher by pressing the On-Off button. 10 156997240en.qxp 12/27/2006 1:39 PM Page 11 Filling with dishwasher salt CAUTION! Use only special salt suitable for dishwashers Only before filling with salt for the first time, fill the salt container with water Using the funnel provided, pour in the salt until the container is filled with salt. Remove any trace of salt. Replace the cap tightly turning it clockwise until it stops with a click. The salt cap has a refill indicator window in the centre in which a green float is clearly visible when there is salt inside the container and almost disappears when the salt has finished. IMPORTANT! Water will overflow from the container as salt is added. IMPORTANT! The salt container will require topping up periodically. IMPORTANT! Immediately start a complete programme. 11 156 ...