GAS HOB ZGS 646X INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance UA RO EE KZ LV LT Important safety information These warnings are provided in the interest of safety. You MUST read them carefully before installing or using the appliance. About Installation, Cleaning and Maintenance · It is mandatory that all operations required for the installation are carried out by a qualified or competent person, in accordance with existing rules and regulations. Ensure a good ventilation around the appliance. A poor air supply could cause lack of oxygen. Ensure that the gas supply complies with the gas type stated on the identification label, placed near the gas supply pipe. Using a gas cooking appliance will produce heat and moisture in the room which it has been installed in. Ensure a continuous air supply, keeping the air vents in good conditions or installing a cooker hood with discharge tube. In case of intensive or long time use of the appliance, make the ventilation more efficient, by opening a window or increasing the electric exhaust fan power. Once you removed all packaging from the appliance, ensure that it is not damaged. Otherwise, contact your dealer before proceeding with the installation. The manufacturer disclaims any responsability should all the safety measures not be carried out. Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by unexperienced persons may cause injury or serious malfunctioning. Refer to your local Service Centre. Always insist on genuine spare parts. · · Ensure that all control knobs are in the OFF position when not in use. Never use steam or steam machines to clean the appliance. · · Child Safety · This appliance has been designed to be operated by adults and children under supervision. Young children MUST NOT be allowed to tamper with the controls or play near or with the oven. This appliance is not intended for use by children or other persons whose physical, sensory or mental capabilities or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction by a responsible person to ensure that they can use the appliance safely. Accessible parts of this appliance may become hot when it is in use. Children should be KEPT AWAY until it has cooled. · · · · · · · Environmental Information · After installation, please dispose of the packaging with due regard to safety and the environment. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. · During Operation · It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred, always ensure that the book is left with the appliance in order that the new owner can get to know the functions of the appliance and the relevant warnings. This appliance has been designed for non professional purpose in private houses only. It is meant to cook edible foodstuff only and MUST NOT be used for any other purposes. It is dangerous to alter the specification in any way. For hygiene and safety reasons, this appliance should be kept clean at all times. A build-up of fats or other foodstuff could result in a fire. Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by unexperienced persons may cause injury or serious malfunctioning. Refer to your local Service Centre. Always insist on genuine spare parts. · · · These instructions are only for the countries stated by the symbol printed on the front cover of this instruction book. · 2 Contents For the User Important safety information Instruction for the User Cleaning and Maintenance Service and original spare parts European guarantee 2 4 5 11 11 For the Installer Instruction for the Installer Technical data Gas connection Adaptation to different types of gas Building In Possibilities for insertion 6 6 7 8 9 10 Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: Safety Instructions Step by step instructions for an operation Hints and Tips Environmental information - This appliance complies with the following E.E.C. Directives: 2006/95 (Low Voltage Directive); 89/336 (Electromagnetical Compatibility Directive); 90/396 (Gas Appliances); 93/68 (General Directives) and subsequent modifications. MANUFACTURER: ELECTROLUX HOME PRODUCTS ITALY S.p.A. Viale Bologna, 298 47100 FORLÌ (Italy) 3 Instruction for the User Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. Hob burners control knobs The hob burners control knobs are situated on the hob right hand side. The symbols on the knobs mean that: there is no gas supply there is maximum gas supply there is minimum gas supply Lighting the burners For easier lighting, proceed before putting a pan on the pan support. To light a burner: 1. push in the relevant knob and turn it anticlockwise to "maximum position". 2. Hold a flame near the burner. 3. Then, check the flame is regular and adjust it as required. If you cannot light the flame even after several attempts, check the "cap" (Fig. 1, lett. A) and the "crown" (Fig. 1, lett. B) are in the correct position. To put the flame out, turn the knob to the symbol . · Always turn the flame down or put it out before taking the pans off the burner. In the absence of electricity, ignition can occur without the electrical device; in this case approach the burner with a flame, push the relevant knob down and turn it anti-clockwise until it reaches the "maximum" position. Do not keep the control knob pressed for more than 15 seconds. If the burner does not light even after 15 seconds, release the control knob, turn it the "off" position and wait for at least one minute before trying to light the burner again. Fig. 1 A - Burner cap B - Burner crown C - Burner body Burner minimum diameter 180 mm 120 mm 80 mm maximum diameter 260 mm 220 mm 160 mm Large (rapid) Medium (semirapid) Small (auxiliary) Using the hob correctly To ensure maximum burner efficiency, it is strongly recommended that you use only pots and pans with a bottom fitting the size of the burner used, so that flame will not spread beyond the bottom of the vessel (see the table beside) (Fig. 2). It is also advisable, as soon as a liquid starts boiling, to turn down the flame so that it will barely keep the liquid simmering. Use only pans or pots with flat bottom. Carefully supervise cookings with fats or oil, since these types of foodstuff can result in a fire, if over-heated. Fig. 2 4 Cleaning and Maintenance General cleaning Wash the enamelled components with warm soapy water. Never use abrasive cleaners Frequently wash the "caps" and the "crowns" with hot soapy water, carefully taking away any built-up of food. Regularly wipe over the hob top using a soft cloth weel wrung out in warm water to which a little liquid detergent has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for non-stick saucepans; - steel wool pads; - bath/sink stain removers. Should the hob top become heavily soiled, it is recommended that a proper cleaning product is used. Fig. 3 Pan supports The pan supports are dishwasher proof. If the marks are particularly difficult to remove, use common non-abrasive cleaners or specific products. Never use steel wool pads or acids. The Burners The burner caps and crowns (Fig. 1) can be removed for cleaning. Wash the burner caps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove. After cleaning, be sure to wipe dry with a soft cloth. Periodic Maintenance Periodically ask your local Service Centre to check the conditions of the gas supply pipe and the pressure adjuster, if fitted. 5 Instruction for the Installer The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. The side walls of the unit in which the hob is going to be installed, must not exceed the height of the working top. Avoid installing the appliance in the proximity of inflammable materials (e.g. curtains, tea towels etc.). THE MANUFACTURER WILL NOT ACCEPT LIABILITY, SHOULD ANY OF THE OTHER SAFETY INSTRUCTIONS INCORPORATED IN THIS BOOK OR THE REGULATION IN FORCE BE IGNORED. Technical data Gas Burners Rating Rapid Burner 3,0 kW (G20) - 2,8 kW (G30/G31) Semirapid Burner 2,0 kW Auxiliary Burner 1,0 kW Appliance Class Category 3 II2H3B/P Natural Gas G20 - 20 mbar G 1/2" Setting Gas connection Hob recess dimensions Length Width 550 mm 470 mm 6 Gas connection Choose fixed connections or use a flexible pipe in stainless steel in compliance with the regulation in force. If using flexible metallic pipes, be careful they do not come in contact with mobile parts or they are not squeezed. Use the same attention when the hob is combinated with an oven. IMPORTANT - To ensure a correct operation, a saving of energy and the long life of the appliance, the voltage pressure of the appliance must correspond to the recommended values. The adjustable connection is fixed to the comprehensive ramp by means of a threaded nut G 1/2". Interpose the sealing between the components as shown in Fig. 4. Screw the parts without forcing, adjust the connection in the required direction and tighten everything. D Connection using flexible non metal pipes When the connection can be easily inspected in its full extent, there is the chance to use a flexible pipe according to the rules in force. The flexible pipe must be tightly fixed using clamps according to the rules in force. LPG : use the rubber pipe holder «D» (Fig. 4). Always insert the gasket «B». Then proceed with the gas connection. The flexible pipe should be made ready for use in such a way that: - nowhere it can reach overtemperature, other than room temperature, higher than 30°C; if the flexible pipe, to reach the cock, must run behind the range, it must be installed as shown in Fig. 4; - it is no longer than 1500 mm; - it shows no throttles; - it is not subject to traction or torsion; - it doesn't get in touch with cutting edges or corners; - it can be easily inspected in order to check its condition. The control of preservation of the flexible pipe consists in checking that: - it doesn't show cracks, cuts, marks of burnings both on the end parts and on its full extent; - the material is not hardened, but shows its normal elasticity; - the fastening clamps are not rusted; - expiry term is not due. If one or more abnormalities are seen, do not repair the pipe, but replace it. Fig. 4 A) B) C) D) Ramp with ending nut Seal Adjustable connection Rubber pipe holder for LPG Important Once installation is complete, check the perfect seal of every pipe fitting, using a soapy solution, never a flame 7 Adaptation to different types of gas Injectors replacement · Remove the pan supports. · Remove the burner's caps and crowns. · With a socket spanner 7 unscrew and remove the injectors (Fig. 5), and replace them with the ones required for the type of gas in use (see table 2). · Reassemble the parts, following the same procedure backwards. · Replace the rating label (placed near the gas supply pipe) with the relevant one for the new type of gas supply. You can find this label in the package of the injectors supplied with the appliance. Should the feeding gas pressure be different or variable compared with the required pressure, an appropriate pressure adjuster must be fitted on the gas supply pipe, in compliance with the rules in force. Fig. 5 Adjustment of minimum level To adjust the minimum level of the burners, proceed as follows: Light the burner. Turn the knob on the minimum position. Remove the knob. With a thin screwdriver, adjust the by-pass screw positioned in the centre of the gas tap control shaft (see Fig. 6). If changing from natural gas 20 mbar to liquid gas, completely tighten the adjustment screw in. If changing from liquid gas to natural gas 20 mbar, undo the by-pass screw about 1/4 of a turn. If changing from natural gas 20 mbar to natural gas 13 ...