User manual ZENITH 50PC3D-UD

LCD TV MODELS: 32LC2D 32LC2DC 37LC2D 42LC2D PLASMA TV MODELS: 42PC3D 42PC3DC 42PC3DV 50PC3D 42PC1DVH 42PC3DH 42PC3DVA 50PC3DH OWNER'S MANUAL Internet Home Page : http://www.lge.com http://www.lg.ca ENERGYSTAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA). As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service. P/NO : 38289U0527B (0605-REV05) Printed in Korea Warning Warning CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. REGULATORY INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CAUTION: Do not attempt to modify this product in any way without written authorization from LG Electronics Corporation. Unauthorized modification could void the user's authority to operate this product. U.S.A. only ----------------------------------------------COMPLIANCE: The responsible party for this product's compliance is: LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 Phone: 1-800-243-0000 http://www.lgusa.com --------------------------------------------------------------- 2 Safety Instructions Safety Instructions WARNING : To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Apparatus To Rain Or Moisture. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. Ow ner's Man ual 2. Keep these instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 3. Heed all warnings. 4. Follow all instructions. 9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 7. Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions. 11. Only use the attachments / accessories specified by the manufacturer. 3 Safety Instructions 12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart / apparatus combination to avoid injury from tip-over. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. Note - If the TV feels cold to the touch, there may be a small "flicker" when when it is turned on. This is normal, there is nothing wrong with TV. - Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance. - Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen. CAUTION concerning the Power Cord Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. On Disposal a. The fluorescent lamp used in this product contains a small amount of mercury. b. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority. 4 Contents Contents 2 3~4 Warnings Safety Instructions Accessories Controls (Model Name: 32/37/42LC2D**) Swivel Stand (42LC2D** only) Connection Options (Model Name: 32/37/42LC2D**) Controls (Model Name: 42PC1D**/42PC3D**/50PC3D**) Connection Options (Model Name: 42PC1D**/42PC3D**/50PC3D**) 7 8 8 9 10 11 Introduction 12~16 Remote Control Key Functions 17 18~20 Various Installation Basic Connection Antenna or Cable Connection VCR Setup External AV Source Setup DVD Setup HDSTB Setup Monitor Out Setup Digital Audio Output PC Setup Turning on the TV Volume Adjustment Channel Selection On Screen Menus Language Selection On Screen Menus Selection and Adjustment EZ Scan (Channel Search) Manual Scan Channel Edit DTV Signal Strength Input Source Input Label EZ Picture APM (Adaptive Picture Mode) Manual Picture Control (EZ Picture-Custom option) Color Temperature Control Video Reset Audio Language EZ SoundRite EZ Sound Manual Sound Control (EZ Sound-Custom option) Stereo/SAP Broadcasts Setup Front Surround TV Speakers On/Off Setup BBE 5 Installation External Equipment Connections 21 22~23 23 24~25 26~27 28 28 29~31 32 32 32 32 33 34 34 35 36 36 37 38 38 39 39 39 40 40 41 41 42 42 43 43 Basic operation Setup Menu Options Operation Video Menu Options Audio Menu Options Contents Time Menu Options Operation 44 44 45 45 46 47 48 48 49 50 50 51 52~53 Auto Clock Setup Manual Clock Setup On/Off Timer Setup Sleep Timer Auto Off Aspect Ratio Control Cinema 3:2 Mode Setup Caption Caption/Text Caption Option Low Power (42PC1D**/42PC3D**/50PC3D** only) ISM (Image Sticking Minimization) Method (42PC1D**/42PC3D**/50PC3D** only) Parental Lock Setup Option Menu Features Lock Menu Options 54~59 60~61 External Control Device Setup IR Codes Programming the Remote Programming Codes Troubleshooting Checklist Maintenance Product Specifications Reference 62 63~64 65~66 66 67~68 6 Introduction Introduction Accessories Ensure that the following accessories are included with your TV. If any accessory is missing, please contact the dealer from where you purchased the product. TV UT INP TV WE PO AU DIO D DV DE MO BLE R UT INP CA DAY ME - VC NU GU ID E DAY R B ST TIO RA R TE EN + EX IT TIM ER L VO TE MU CC INF GE PA O V FA 1 GE PA 4 2 7 5 C H 3 EZ PIC EZ AD JU ST AP M SA P DAY 8 6 0 9 K HB AS FL EE FR ZE ME - NU ID GU D UN SO R TE EN 1.5V 1.5V EX IT ER TIM VO CC L TE MU INF GE PA O V FA 1 GE PA 4 7 H C 2 5 3 EZ PIC AD JU ST M AP 8 6 0 EZ D UN SO SA P 9 K HB AS FL EE FR ZE Power Cord 75 Round Cable D-sub 15 pin cable Owner's Manual Remote Control / Batteries For 42PC1D**, 42PC3D**, 50PC3D** For 32/37/42LC2D** 42LC2D** only 32LC2D** only 2-Wall brackets 2-eye-bolts 42PC1D**, 42PC3D** only Twister Holder 2-TV brackets Arrange the wires 2-Wall brackets with the twister holder. Polishing Cloth Polish the TV with the cloth. 4-bolts for stand assembly See below for detail information. 2-bolts (Refer p.19) 2-TV Bracket Bolts Cable Management (Refer p.18) Stand Installation for 32LC2D** 1 Carefully place the product screen side down on a cushioned surface that will protect product and screen from damage. 2 Place the hook of the stand in the back of the product as shown. 3 Install the 4 bolts provided securely, in the back of the product. 7 Introduction Controls (Model Name: 32/37/42LC2D**) - This is a simplified representation of front panel. - Here shown may be somewhat different from your TV. CH CHANNEL (D, Buttons E) VOL VOLUME (F,G) Buttons ENTER Button ENTER MENU R MENU Button INPUT Button (Power) Button INPUT Remote Control Sensor Power/Standby Indicator · illuminates red in standby mode. · illuminates green when the set is switched on. Swivel Stand (42LC2D** only) 30° 30° - The TV can be conveniently swivelled on its stand 30° to the left or right to provide the optimum viewing angle. R 8 Introduction Connection Options (Model Name: 32/37/42LC2D**) - Here shown may be somewhat different from your TV. 37/42LC2D** S-VIDEO 32LC2D** S-VIDEO S-VIDEO Input R L/MONO L/ MONO AUDIO R AUDIO Input VIDEO Input AUDIO L/MONO L/ MONO VIDEO VIDEO AV IN 2 AC IN AV IN 2 AV OUT AV IN1 AV OUT (MONO) VIDEO AUDIO S-VIDEO VIDEO AUDIO AV IN 1 COMPONENT IN COMPONENT IN 1/2 AC IN HDMI / DVI IN RS-232C INPUT (CONTROL&SERVICE) AC IN ANTENNA IN HDMI/DVI IN RS-232C IN DIGITAL AUDIO (CONTROL & SERVICE) OUT CABLE IN RGB IN REMOTE CONTROL IN OPTICAL PTICAL AUDIO (RGB/DVI) RGB (PC/DTV) (PC DTV) CABLE IN ANTENNA IN DIGITAL AUDIO OUT OPTICAL AUDIO (RGB/DVI) RGB (PC/DTV) REMOTE CONTROL Port 9 Introduction Controls (Model Name: 42PC1D**/42PC3D**/50PC3D**) - This is a simplified representation of front panel. - Here shown may be somewhat different from your TV. 42PC1D** INPUT MENU ENTER VOL CH INPUT Button Power/Standby Indicator · illuminates red in standby mode. · illuminates green when the set is switched on. ENTER Button MENU Button CHANNEL (D, Buttons VOLUME (F,G) Buttons E) (Power) Button 42PC3D**/50PC3D** CH CHANNEL (D, Buttons E) VOL VOLUME (F,G) Buttons ENTER ENTER Button MENU MENU Button INPUT INPUT Button Remote Control Sensor (Power) Button Power/Standby Indicator · illuminates red in standby mode. · illuminates green when the set is switched on. 10 Introduction Connection Options (Model Name: 42PC1D**/42PC3D**/50PC3D**) - Here shown may be somewhat different from your TV. AV IN 2 S-VIDEO Input AUDIO Input VIDEO Input S-VIDEO R AUDIO L/MONO L/ MONO VIDEO AV OUT AV IN1 AV OUT (MONO) VIDEO AUDIO S-VIDEO VIDEO AUDIO AV IN 1 COMPONENT IN COMPONENT IN 1/2 HDMI/DVI IN RS-232C INPUT (CONTROL&SERVICE) AC IN ANTENNA IN RGB IN HDMI/DVI IN RS-232C IN DIGITAL AUDIO (CONTROL & SERVICE) OUT CABLE IN AUDIO (RGB/DVI) REMOTE CONTROL IN AC IN OPTICAL PTICAL RGB (PC DTV) (PC/DTV) CABLE IN ANTENNA IN DIGITAL AUDIO OUT OPTICAL AUDIO (RGB/DVI) RGB (PC/DTV) REMOTE CONTROL Port 11 Introduction Remote Control Key Functions POWER Turns your TV or any other programmed equipment on or off, depending on mode. TV INPUT Rotates the input mode between Antenna and Cable. In AV12, Component 1-2, RGB-DTV (or RGB-PC), and HDMI/DVI input sources, screen returns to the last TV channel. INPUT (Refer to p.14) External input modes rotate in regular sequence: Antenna, Cable, AV1-2, Component 1-2, RGB-DTV (or RGB-PC), HDMI/DVI). (AV1, AV2,Component 1-2 input sources are linked automatically, Only if these are connected) TV INPUT POWER INPUT TV DVD MODE VCR AUDIO CABLE STB DAY - DAY+ MENU GUIDE RATIO ENTER MODE Selects the remote operating mode: TV, DVD, VCR, AUDIO, CABLE, or STB. Select a mode other than TV, for the remote to operate an external device. EXIT TIMER CC INFO MENU Brings up the main menu to the screen. GUIDE (Refer to p.16) Shows program schedule. RATIO (Refer to p.47) Changes the aspect ratio. PAGE VOL MUTE FAV PAGE CH 1 4 7 2 5 8 0 3 6 9 FLASHBK THUMBSTICK (Up/Down/Left/Right/ENTER) Allows you to navigate the on-screen menus and adjust the system settings to your preference. EZ PIC EZ SOUND ADJUST APM SAP FREEZE EXIT Clears all on-screen displays and returns to TV viewing from any menu. TIMER (Refer to p.45) Lets you select the amount of time before your TV turns itself off automatically. CC (Refer to p.49) Select a closed caption: Off, CC1~4, Text1~4. INFO (Refer to p.15) When you watch the TV, information displays on top of the screen. Not available in Component 1-2, RGB and HDMI/DVI mode. 12 Introduction VCR/DVD/DVHS/Camcorder BUTTONS Control some video cassette recorders or DVD players ("RECORD" button is not available for DVD player). TV INPUT POWER INPUT DAY + / DAYMoves forward or backward in 24 hour increments. TV DVD MODE VCR AUDIO CABLE STB VOLUME UP/DOWN Increases/decreases the sound level. CHANNEL UP/DOWN Selects available channels found with EZ scan and Manual scan. DAY - DAY+ MENU GUIDE RATIO PAGE UP/DOWN Moves from one full set of screen information to the next one. MUTE Switches the sound on or off. FAV Use to scroll the Favorite channels. ENTER EXIT TIMER CC INFO PAGE NUMBER BUTTONS CH VOL MUTE FAV PAGE -- (DASH) Used to enter a program number for multiple program channels such as 2-1, 2-2,etc. FLASHBK Returns to the last channel viewed. 1 4 7 2 5 8 0 3 6 9 FLASHBK EZ PIC EZ SOUND ADJUST APM SAP FREEZE EZ PIC (Refer to p.38) Selects a factory preset picture mode depending on the viewing environment. EZ SOUND (Refer to p.41) Selects the sound appropriate for the program's character. SAP (Refer to p.42) Selects MTS sound: Mono, Stereo, and SAP in analog mode. Change the audio language in DTV mode. FREEZE Freezes the currently-viewed picture. ADJUST (Refer to p.31) Adjusts screen position, size, and phase in PC mode. APM (Refer to p.38) Concurrently, compare with the Daylight, Normal, Night Time and Custom on the screen. 13 Introduction TV INPUT POWER INPUT INPUT Auto Link 1. When every external equipment is connected: Antenna Cable AV1 AV2 Component1 TV DVD MODE VCR AUDIO CABLE STB HDMI/DVI DAY DAY+ RGB-DTV (or RGB-PC) Component2 MENU GUIDE RATIO 2. When any external equipment is not connected: Antenna Cable RGB-DTV (or RGB-PC) HDMI/DVI ENTER 3. When some External Equipment is connected: (ex: When connected to AV IN1) EXIT TIMER CC INFO Antenna Cable AV1 PAGE VOL MUTE FAV PAGE CH HDMI/DVI RGB-DTV (or RGB-PC) · You can also select Input Source in the SETUP menu. 3 6 9 FLASHBK SETUP 1 4 7 2 5 8 0 VIDEO AUDIO TIME EZ Scan Manual Scan Channel Edit DTV Signal Input Source Input Label Set ID G Antenna Cable AV1 AV2 Component1 Component2 RGB-PC HDMI/DVI OPTION EZ PIC EZ SOUND ADJUST APM SAP FREEZE LOCK MENU Previous · Antenna: Select it when watching the TV/DTV. · Cable: Select it when watching the CATV/CADTV. · AV1, AV2: Select it when watching the VCR or external equipment. · Component 1-2: Select it when using the DVD or the Digital set-top box depend on connector. · RGB-PC / RGB-DTV: Select it when using PC or Digital set-top box depend on connector. · HDMI / DVI: Select it when using DVD, PC or Digital set-top box depend on connector. 14 Introduction