User manual ZENITH D32D51 - OPERATING GUIDE

machine numbers D 27D 51 D32D51 D36D51 ® enjoy the view table of contents page 5 © Copyright 2001, Zenith Electronics Corporation. operating guide / warranty RECORD YOUR MODEL NUMBER The model and serial number of your Entertainment MachineTM are located on the back of the TV cabinet. For your future convenience, we suggest that you record these numbers here: Model No._________________________ Serial No. __________________________ WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. POWER CORD POLARIZATION: CAUTION: To prevent electric shock, match wide blade of plug to wide slot, fully insert. ATTENTION: Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu'au fond. NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the cable TV system installer's attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. REGULATORY INFORMATION: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. CAUTION: Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation. Unauthorized modification could void the user's authority to operate this product. COMPLIANCE: The responsible party for this product's compliance is: Zenith Electronics Corporation, 2000 Millbrook Drive, Lincolnshire, IL 60069, USA · Phone: 1-847-391-7000. Entertainment MachineTM is a trademark of Zenith Electronics Corporation © Copyright 2001 Zenith Electronics Corporation IMPORTANT SAFETY INSTRUCTIONS Important safeguards for you and your new product Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference. Observing the simple precautions discussed in this operating guide can help you get many years of enjoyment and safe operation that are built into your new product. This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association. 1. Read Instructions All the safety and operating instructions should be read before the product is operated. 9. Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards. 2. Follow Instructions All operating and use instructions should be followed. 10. Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 3. Retain Instructions The safety and operating instructions should be retained for future reference. 4. Heed Warnings All warnings on the product and in the operating instructions should be adhered to. 5. Cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 11. Power Sources This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 6. Water and Moisture Do not use this product near water for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool. 12. Power Cord Polarization This product is equipped with a polarized alternating - current power plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. 7. Accessories, Carts, and Stands Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. 13. Power Cord Protection Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 8. Transporting Product A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. (Continued on next page) PORTABLE CART WARNING 206-3706 2-WR-POLZ PAGE 3 IMPORTANT SAFETY INSTRUCTIONS (Continued from previous page) 14. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. Example of Grounding According to National Electrical Code Instructions short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 19. Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 20. Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. If the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. e. If the product has been dropped or the cabinet has been damaged. f. If the product exhibits a distinct change in performance. Ground Clamp Antenna Lead in Wire Antenna Discharge Unit (NEC Section 810-20) Grounding Conductor (NEC Section 810-21) Ground Clamps Power Service Grounding Electrode System (NEC Art 250, Part H) Electric Service Equipment NEC - National Electrical Code 21. Replacement Parts 15. Lightning For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 22. Safety Check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 16. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 23. Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. 17. Overloading Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 24. Heat The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. 18. Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or PAGE 4 3-WireRev6/00 Table of Contents Refer to the information below to hook up external equipment and set up the features on your Entertainment Machine Step 1. Hook up external equipment and antenna or cable service wires to the TV. Install batteries in the remote control. After all connections have been made, plug your TV into standard household power, see pages 7 thru 14. Step 2. Go to page 18 to EZ program the TV. Step 3. Set up all other TV options see pages listed below. Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Safety Information . . . . . . . . . . . . . . . . . . . . 3 - 4 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Video Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Contrast, Brightness, Color, Tint, Sharpness, Color Temp: . . . . (Cool, Warm), EZ Picture: (Custom, Normal, Movie, Digital Pres, Video Game, Sports, Night Time, Weak Signal). Video Sub Menu, Aspect Ratio and other settings . . . . . . 30 Audio Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Bass, Treble, Balance, Audio Mode: (Stereo, Mono, SAP), EZ Bass Front Surround, EZ SoundRite, Speakers, EZ Sound: (Custom, Normal, Stadium, News, Music, Theater). Lock (Parental Control Menu) . . . . . . . . . . . . . . . 32 - 33 - 34 Restricts viewer programming. Special Menu EZ Timer: Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . 35 EZ Timer: On/Off Timer Functions . . . . . . . . . . . . . . . . . 36 Channel Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 XDS Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 PIP Menu (Setup PIP picture appearance) . . . . . . . . . . . 39 Source Sense . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Source Hookup Options . . . . . . . . . . . . . . . . . . . . . . . 41 EZ Demo (On-screen menus overview) . . . . . . . . . . . . . . 42 PIP (Picture-in-Picture) . . . . . . . . . . . . . . . . . . . . . . 43 - 44 Remote Control Programming Set up remote to operate other devices . . . . . . . . . . . . . 45 Amplifier Volume Override . . . . . . . . . . . . . . . . . . . . . . 46 Aux 1 -2 -3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 AutoFind . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Programming Product Brand Codes . . . . . . . . . . . . . 49 - 50 Remote Modes Key Functions . . . . . . . . . . . . . . . . . . . . 51 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 53 - 54 - 55 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 - 58 Recommended Accessories . . . . . . . . . . . . . . . . . . . . . . . . 59 Zenith Warranty . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover Step 1. Hook Up TV Connection Panel Overview . . . . . . . . . . . . . . . . . . . . . . . . 6 Equipment Connection Options Antenna, Install batteries in remote control . . . . . . . . . . . . . . 7 Cable Service, Install batteries in remote control . . . . . . . . . . 8 Antenna with VCR, Install batteries in remote control . . . . . . . 9 Cable Service with VCR, Install batteries in remote control . . . 10 S-VHS VCR, Install batteries in remote control . . . . . . . . . . . 11 DVD Component Video Hookup . . . . . . . . . . . . . . . . . . . . . 12 High-Definition Hookup . . . . . . . . . . . . . . . . . . . . . . . . . . 13 High-Definition/RGB Hookup . . . . . . . . . . . . . . . . . . . . . . . 14 Audio/Video Signal Output . . . . . . . . . . . . . . . . . . . . . . . . 15 Front Panel Controls/Inputs . . . . . . . . . . . . . . . . . . . . . . . 16 Remote Control Key Functions in TV mode . . . . . . . . . . . . . . 17 Step 2. Reception Setup and Channel Search EZ Program: Select Cable service or Air Antenna and run channel search . . . . . . . . . . . . . . . . . . . . . . . . On-Screen Menu Operation with Remote . . . . . . . . . . . . . . . On-Screen Menus/Displays Overview . . . . . . . . . . . . . . . 20 Other Functions and On-Screen Displays . . . . . . . . . . . . . . . 18 19 21 22 Step 3. Customize the TV's Features Setup Menu (Start with page 18, Add/Del/Surf . . . . . . . . . . . EZ Clock Set . . . . . . . . . . . Captions (Caption/Text) . . . . Language . . . . . . . . . . . . . Source . . . . . . . . . . . . . . Background . . . . . . . . . . . EZ .. .. .. .. .. .. Program) ....... ....... ....... ....... ....... ....... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 24 25 26 27 28 Note: Design and specifications are subject to change without prior notice. 206-3594 PAGE 5 "Source" Connection Panel Overview To hook up source equipment,see below and also refer to the Table of Contents on page 5; shows pages to go to for equipment hookup options. Also, see the front connections panel source's hookup options on page 16. After you have finished hooking up your source equipment, go to page 18 and use EZ Program to search for and find all the available channels in your area. TV Back HD IN DVD IN VIDEO 1 IN VIDEO 2 IN MONITOR OUTPUT Y Pr RGB Y S-VIDEO 1 S-VIDEO 2 Pr VIDEO VIDEO VIDEO ANTENNA CABLE Pb R AUDIO Pb R AUDIO R AUDIO R AUDIO R AUDIO ANTENNA/CABLE Use to hookup your antenna or cable system. See pages 7, 8, 9, 10, 11. L L L MONO L MONO L HD-RGB INPUT Connect HD-RGB output to this connector. See page 14. HD IN Connect your highdefinition equipment to these jacks. See page 13. DVD IN Connect your DVD player to these jacks. See page 12. VIDEO 1 IN VIDEO 2 IN Connect your Audio/Video or S-Video equipment to these jacks. See pages 9, 10, 11. VIDEO / R - L AUDIO OUT Use these output jacks to connect external audio/video equipment. See page 15. PAGE 6 206-3594 Hook Up an Off-Air Antenna Connect an off-air antenna 1 2 3 Locate the Antenna/Cable jack on the back of your Entertainment Machine. Connect the wire that runs from the wall directly to this jack, according to one of the diagrams to the right. Remove the back of the remote and put in two "AAA" batteries. Flat Wire (300 ohm) Antenna Typical TV Back ANTENNA CABLE Back of Remote 300/75 ohm Adapter 4 Plug in your TV. Do not plug it into an outlet controlled by a switch. Your Entertainment Machine is designed to operate on standard household current, 120-volt 60 Hertz AC. Do not attempt to operate it on DC power. Typical TV Back Antenna 120 V AC 60 Hz ANTENNA CABLE If you have a 75 ohm RF cable, then you don't need any adapters! A 300 to 75 ohm adapter is not included with the TV. RF Coaxial Wire (75ohm) Mini glossary 75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire sticking through the middle, and it screws onto the threaded jack on the back of your TV. A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws on one end and a round opening with a wire sticking out on the other end. 300 TO 75 OHM ADAPTER 206-3594 PAGE 7 Hook Up Cable Service (CATV) Connect cable service to your Entertainment Machine 1 2 Locate the Antenna/Cable jack on the back of the TV. Connect the cable service wire that runs from the wall or cable box directly to this jack, according to one of the diagrams to the right. Remove the back of the remote and put in two "AAA" batteries. Typical TV Back Typical Cable TV Wall Jack 3 ANTENNA CABLE Back of Remote Coaxial Round Wire (75ohm) 4 Plug in the TV. Do not plug it into an outlet controlled by a switch. Your TV is designed to operate on standard household current, 120-volt 60 Hertz AC. Do not attempt to operate it on DC power. Typical Cable TV Wall Jack 120 V AC 60 Hz In Out Cable Box output switch 3 4 Typical TV Back If you're using a cable box, leave the TV on channel 3 or 4 and use your cable box to change channels. ANTENNA CABLE If you're using a cable box, EZ Program might only find the channel your cable service is on (usually channel 3 or 4). Don't worry, that's all you need! RF Coaxial Wire (75ohm) PAGE 8 206-3489-O Hook Up an Off-Air Antenna and VCR Connect your off-air antenna and VCR to your Entertainment Machine 1 2 3 Locate the Antenna In jack on the back of the VCR. Connect the wire that runs from the antenna, according to the diagram to the right. Make any other connections as necessary. Remove the back of the remote and put in two "AAA" batteries. RF Coaxial Round Wire (75ohm) Typical Antennas: Flat or Round Wire VCR Back VCR Back AV Panel In Out output switch 3 4 Audio Video Flat Wire (300 ohm) Back of Remote 300/75 ohm Adapter 4 Plug in the TV. Do not plug it into an outlet controlled by a switch. The TV is designed to operate on standard current, 120-volt 60 Hertz AC. Do not attempt to operate it on DC power. TV Back 120 V AC 60 Hz HD IN DVD IN VIDEO 1 IN VIDEO 2 IN MONITOR OUTPUT Y Y S-VIDEO 1 S-VIDEO 2 No adapters or A/V cables are included with the TV. See your Zenith dealer to purchase any adapters or cables. Without A/V cables, most VCRs will not play videocassettes in stereo sound. ANTENNA CABLE Pr RGB Pr VIDEO VIDEO VIDEO Pb R AUDIO Pb R AUDIO R AUDIO R AUDIO R AUDIO L L L MONO L MONO L Connect your VCR to the Video 1 or Video 2 set of input jacks 206-3594 PAGE 9 Hook Up Cable Service (CATV) and VCR Typical Cable TV Wall Jack Connect Cable service and a VCR to the TV VCR Back In Out Cable Box output switch 3 4 VCR Back AV Panel 1 2 Locate the Antenna/Cable In jack on the back of the VCR. Connect the cable service wire that runs from the wall, according to one of the diagrams to the right. Make any other connections necessary for your setup. Remove the back of the remote and put in two "AAA" batteries. Cable service with or without a cable box In Out output switch 3 4 Audio Video 3 Typical Cable TV Wall Jack Back of Remote 4 Plug in the TV. Do not plug it into an outlet controlled by a switch. The TV is designed to operate on standard current, 120-volt 60 Hertz AC. Do not attempt to operate it on DC power. TV Back 120 V AC 60 Hz HD IN DVD IN VIDEO 1 IN VIDEO 2 IN MONITOR OUTPUT Y Pr Y S-VIDEO 1 S-VIDEO 2 Pr VIDEO VIDEO VIDEO Tune both the VCR and the television to channel 3 or 4 (cable box output channel) and use the cable box to change channels. No A/V cables are included with your TV. Without A/V cable hookups, most VCRs will not play videocassettes in stereo sound. RGB ANTENNA CABLE Pb R AUDIO CB Pb R AUDIO R AUDIO R AUDIO R AUDIO L L L MONO L MONO L Connect your VCR to the Video 1 or Video 2 set of input jacks PAGE 10 206-3594 Hook Up S-VHS VCR Your Zenith TV may be connected to a Super-VHS VCR through the S-Video Input located on the front or rear source connection panels on your TV From Antenna or Cable Service With or Without a Cable Box VCR Back VCR Back AV Panel In output switch 3 4 S-Video Out 1 2 Hook up your S-VHS VCR to your Zenith TV according to the diagram shown at the right. Remove the back of the remote and put in two "AAA" batteries. Flat Wire (300 ohm) Audio Out RL Out Back of Remote 300/75 ohm Adapter 3 Plug in your TV. Do not plug it into a switched outlet. Your Zenith TV is designed to operate on standard household current, 120-volt 60 Hertz AC. Do not attempt to operate it on DC power. TV Back 120 V AC 60 Hz 4 On the remote, press SOURCE repeatedly until "S-Video" is displayed. Or use the Source menu to choose the S-Video input the equipment is connected to. HD IN DVD IN VIDEO 1 IN VIDEO 2 IN MONITOR OUTPUT Y Pr RGB Y S-VIDEO 1 S-VIDEO 2 Pr VIDEO VIDEO VIDEO ANTENNA CABLE Pb R AUDIO Pb R AUDIO R AUDIO R AUDIO R AUDIO L L L MONO L MONO L Connect your S-Video VCR to the S-Video 1 or S-Video 2 set of input jacks 206-3594 PAGE 11 Hook Up Component Video Equipment Connecting component video DVD equipment TV Back 1 2 Make the connections as indicated. (Appearance of components may vary from those in the illustrations.) Plug in your TV. Do not plug it into a switched outlet. Your Entertainment Machine is designed to operate on standard household current, 120volt 60 Hertz AC. Do not attempt to operate it on DC power. HD IN DVD IN VIDEO 1 IN VIDEO 2 IN MONITOR OUTPUT Y Pr RGB Y S-VIDEO 1 S-VIDEO 2 Pr VIDEO VIDEO VIDEO Pb R AUDIO 120 V AC 60 Hz Pb R AUDIO R AUDIO R AUDIO R AUDIO L L L MONO L MONO L 3 4 Press POWER to turn TV on. On the remote, press SOURCE repeatedly until "DVD" is displayed. Or use the Source menu to choose DVD. Y Pr Pb R L COMPONENT VIDEO OUT S-VIDEO OUT VIDEO R-AUDIO L-/MONO Component video jacks are sometimes labeled with CR, CB, or PB, PR. In this case, connect B to B and the R to R. The "Y" jack is usually labeled "Y", connect Y to Y. DVD Player with Component Video PAGE 12 206-3594 Hook Up HD Equipment Connecting high-definition equipment TV Back 1 2 Make the HD connections as indicated. (Appearance of components may vary from those in the illustrations.) Plug in your TV. Do not plug it into a switched outlet. Your Entertainment Machine is designed to operate on standard household current, 120-volt 60 Hertz AC. Do not attempt to operate it on DC power. ANTENNA CABLE HD IN DVD IN VIDEO 1 IN VIDEO 2 IN MONITOR OUTPUT Y Pr RGB Y S-VIDEO 1 S-VIDEO 2 Pr VIDEO VIDEO VIDEO Pb R AUDIO Pb R AUDIO R AUDIO R AUDIO R AUDIO 120 V AC 60 Hz L L L MONO L MONO L 3 4 Press POWER to turn TV on. On the remote, press SOURCE repeatedly until "HD-In" is displayed. Or use the Source menu to choose HD-In. Y Pr Pb R L HD OUT S-VIDEO OUT VIDEO R-AUDIO L-/MONO Set Top Box with Component Video 206-3594 PAGE 13 Hook Up HD-RGB Equipment Connecting High-definition RGB output equipment TV Back 1 2 Make the RGB connections as indicated. (Appearance of components may vary from those in the illustrations.) Plug in your TV. Do not plug it into a switched outlet. Your Entertainment Machine is designed to operate on standard household current, 120-volt 60 Hertz AC. Do not attempt to operate it on DC power. HD IN DVD IN VIDEO 1 IN VIDEO 2 IN MONITOR OUTPUT Y Pr RGB Y S-VIDEO 1 S-VIDEO 2 Pr VIDEO VIDEO VIDEO Pb R AUDIO Pb R AUDIOO AUDI R AUDIO R AUDIO R AUDIO 120 V AC 60 Hz L L L MONO L MONO L 3 4 Press POWER to turn TV on. On the remote, press SOURCE repeatedly until "HD-RGB In" is displayed. Or use the Source menu to choose HD-RGB In. RGB Out R Audio Out L Set Top Box with HD-RGB Output PAGE 14 206-3594 Audio/Video Signal Output Output to Audio/Video devices