User manual ZENITH Z20LA7R - OPERATING GUIDE

Operating Guide | Warranty Model Number | Z15LA7R Z20LA7R | LCD TV © Copyright 2004, LG Electronics USA, Inc. Warning Warning CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. REGULATORY INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CAUTION: Do not attempt to modify this product in any way without written authorization from LG Electronics Corporation. Unauthorized modification could void the user's authority to operate this product. COMPLIANCE: The responsible party for this device compliance is: Zenith Electronics Corporation 1-201-816-2000 Marked and Distributed in the United States by LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 http://www.zenith.com 2 Safety Instructions Safety Instructions WARNING : To reduce the risk of fire or electric shock, DO NOT expose this apparatus to rain or moisture. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. CAUTION : These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use the attachments / accessories specified by the manufacturer. 3 Safety Instructions Safety Instructions continued 12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart / apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. On Disposal a. The fluorescent lamp used in this product contains a small amount of mercury. b. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority. 4 Contents Contents Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4 Introduction Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Connection Options . . . . . . . . . . . . . . . . . . . . . . 7 Remote Control Key Functions . . . . . . . . . . . . . .8 Installation Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Kensington Security System . . . . . . . . . . . . . . . .9 Installation Instruction . . . . . . . . . . . . . . . . . . . . . .10 External Equipment Connections . . . . . . . . . .11~14 Antenna Connection . . . . . . . . . . . . . . . . . . . . .11 VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Cable TV Setup . . . . . . . . . . . . . . . . . . . . . . . .12 DTV Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 External A/V Source Setup . . . . . . . . . . . . . . . .13 DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Using Headphones . . . . . . . . . . . . . . . . . . . . . .14 PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Sound Menu Options EZ Audio . . . . . . . . . . . . . . . . Equalizer Adjustments . . . . . . AVL (Auto Volume Leveler) . . . Sound Balance . . . . . . . . . . . . Stereo/SAP Broadcasts Setup Time Menu Options Auto Clock Setup . . . . . . . . . . Manual Clock Setup . . . . . . . . On/Off Timer Setup . . . . . . . . Sleep Timer Setup . . . . . . . . . Auto Off . . . . . . . . . . . . . . . . . Special Menu Options Closed Captions . . . . . . . . . . . Caption/Text . . . . . . . . . . . . . . Captions . . . . . . . . . . . . . . . . . Key Lock . . . . . . . . . . . . . . . . Lock Options . . . . . . . . . . . . . . . Lock Menu Setup . . . . . . . . . . . . . . . . . . . . . . .19 . . . . . . . . . . . . .19 . . . . . . . . . . . . .19 . . . . . . . . . . . . .19 . . . . . . . . . . . . .19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 .20 .21 .21 .21 .22 .23 .23 .23 .24 .25 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . .26 Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .27 Operation PC Menu Options . . . . . . . . . . . . . . . . . . . . . . . . .15 TV Operation Overview . . . . . . . . . . . . . . . . . . . .16 Menu Language Selection . . . . . . . . . . . . . . . . . .16 Channel Menu Options Memorizing the Channels with EZ Scan . . . . . .17 Add/Delete Channels with Manual Program . . .17 Favorite Channels Setup . . . . . . . . . . . . . . . . . .17 Picture Menu Options EZ Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Manual Picture Control (User option) . . . . . . . .18 5 Introduction Introduction Controls Side Control Panel Channel Buttons ch vol enter menu tv/video Volume Buttons Enter Button Menu Button TV/Video Button On/Off Button R /I on/off Remote Control Sensor Power/Standby Indicator Glows red in Standby mode, Glows green when the TV is turned on. 6 Introduction Connection Options * Kensington Security System Connector (Refer to P.9) Z15LA7R PC Input PC sound Input AC INPUT Y PB PR H/P S-VIDEO VIDEO (MONO) L VIDEO IN AUDIO R PC INPUT ANT IN +75 COMPONENT(480i/480p/720p/1080i) DVD/DTV IN PC SOUND AC Input DVD/DTV Input S-Video Input Audio / Video Input Antenna Input Headphone Jack Z20LA7R * AC INPUT Y PB COMPONENT(480i/480p) DVD/DTV IN PR H/P S-VIDEO VIDEO (MONO) L VIDEO IN AUDIO R FOR SERVICE ANT IN +75 * : No function - This manual mainly explains the features for the Z15LA7R. 7 Introduction Remote Control Key Functions - When using the remote control, aim it at the remote control sensor on the TV. mute Switches the sound on or off. tv/video Selects: TV, Video, S-Video, Component or PC(only Z15LA7R) mode. fcr (Favorite Channels Review) Press to step through favorite channels. (Refer to p.17) exit mute power multimedia Selects: TV, Component or PC(only Z15LA7R) mode. tv/video multimedia mts power mts Press to step through audio signal settings (Mono, MTS Stereo, and SAP). (Refer to p.19) menu Activates/Deactivates the on-screen menu system. enter fcr exit menu ch enter vol ch vol 1 2 5 8 0 3 6 9 video ch D / E (Channel button) vol F / G (Volume button) number buttons 4 7 audio audio Press to step through sound settings. (Refer to p.19) cc (Closed Captions) Press to step through Closed Caption settings. (Refer to p.23) cc flashbk sleep video Press to step through picture appearance settings (Clear, Optimum, Soft, and User) (Refer to p.18) sleep Sleep timer. Press to step through available times. (Refer to p.21) flashbk Press the flashbk button to return to the last channel you were watching. Installing Batteries · Open the battery compartment cover on the back side and insert the batteries with correct polarity. · Install two 1.5V batteries of AAA type. Don't mix used batteries with new batteries. 8 Installation Installation mute power tv/video multimedia mts Accessories fcr exit menu ch enter vol ch vol 1 4 7 audio 2 5 8 0 3 6 9 video cc flashbk sleep 1.5V 1.5V Owner's Manual AAA Batteries Power Cord Remote Control PC Signal Cable (Z15LA7R Only) PC Sound Cable (Z15LA7R Only) Tie Bands - Arrange the wires with the tie bands. NOTES a. If the TV feels cold to the touch, there may be a small "flicker" when when it is turned on. This is normal, there is nothing wrong with TV. b. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance. c. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen. Kensington Security System - Note: The Kensington Security System is an optional accessory. - The TV is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security System cable as shown below. - For the detailed installation and use of the Kensington Security System, refer to the user's guide provided with the Kensington Security System. For further information, contact http://www.kensington.com, the internet homepage of the Kensington company. Kensington sells security systems for expensive electronic equipment such as notebook PCs and LCD projectors. 9 Installation Installation Instruction Rear A/V Cover * The connection panel is hidden behind the A/V cover. a. Remove the cover. b. Install wires as necessary. c. Reinstall the cover. Align the holes on the TV back panel with the two tabs on the rear A/V cover as shown. d. Close cover. W ire Holders - Thread, then pull the wires through the hole on the TV stand. Adjusting the TV Viewing Angle Viewing - You can adjust the vertical angle of the TV between -3° and 12°. 0° Approx. -3° Approx. 12° 10 Installation External Equipment Connections - This manual mainly explains the features for the Z15LA7R. Antenna Connection - For optimum picture quality, adjust antenna direction. Connecting to an Inside Antenna Setup - Typical wall antenna jack used in apartment buildings, connect the antenna cable as shown below. (Use the correct type of antenna cable for the type of wall antenna jack.) Turn clockwise to tighten. PC INPUT ANT IN +75 Bronze Wire 75 Round Cable Antenna Converter 300 Flat Wire Apartment Buildings Wall Connection Jack Antenna Jack - If you have a 75 round cable, insert the bronze wire and then tighten the connection nut. If you have a 300 flat wire, connect the twisted wire to the antenna converter and then connect the converter to the antenna jack on the TV. - If using 75 round cable, do not bend the bronze wire. It may cause poor picture quality. Connecting to an Outdoor Antenna Setup - This type of antenna is commonly used in single family dwellings. VHF Antenna Turn clockwise to tighten. UHF Antenna PC INPUT ANT IN +75 75 Round Cable Bronze Wire 300 Flat Wire Antenna Jack Single Family Home Antenna Converter - In poor signal areas, to get better picture quality, install a signal amplifier to the antenna as shown to the right. - If signal needs to be split for two TVs, use an antenna signal splitter for connection. VHF UHF PC INPUT ANT IN +75 Signal Amplifier 11 Installation External Equipment Connections Continued VCR Setup - A VCR can be setup in two different ways. The most common connection is Connection 1 but requires the TV to be tuned to channel 3 or 4 to view input from the VCR. Connection 1 1. Connect the coaxial cable output on the VCR to the antenna input on the TV. 2. Connect the coaxial cable from the wall to the input on the VCR. 3. Set VCR switch to 3 or 4 and then tune TV to the same channel number. AC INPUT Y PB PR H/P S-VIDEO VIDEO (MONO) L VIDEO IN AUDIO R PC INPUT ANT IN +75 COMPONENT(480i/480p/720p/1080i) DVD/DTV IN PC SOUND Connection 2 1. Connect your cable and/or antenna connection to the input(s) of the VCR. 2. Connect the audio/video output jacks on the VCR to the corresponding input jacks on the TV, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). 3. Insert a video tape into the VCR and press PLAY on the VCR. 4. Use the tv/video button on the remote control to select Video. If connected to S-VIDEO on side panel, select the S-Video external input source.) Typical Antennas ANT IN 2 1 S-VIDEO OUT IN CH4 ANT OUT VCR VIDEO (R) AUDIO (L) Direct Connection CH3 NOTE In Video mode, TV automatically reverts to TV mode if the fcr button or flashbk buttons are pressed. Cable TV Setup - If your cable service does not require a converter box, refer to the Antenna Connection instructions. - After subscribing to a local cable TV service and installing a converter, you can watch cable TV programming. - For further cable TV information, contact a local cable service provider. Connection 1 1. Connect the coaxial cable output on the cable box to the antenna input on the TV. 2. Connect the coaxial cable from the wall to the input on the cable box. 3. Set the channel switch to 3 or 4 and then tune TV to the same channel number. Connection 2 1. Connect your cable input of the cable box. 2. Connect the audio/video output jacks on the cable box to the corresponding input jacks on the TV, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). 3. Use the tv/video button on the remote control to select Video. If connected to S-VIDEO on side panel, select the S-Video external input source. Important Note: If your cable box has Component Video outputs or DVI, it is recommend you use those connections for the best quality picture. High Definiton input on this LCD TV is only supported on these two connections. When using DVI there are three connections to each device, the DVI cable plus the two audio cables. When using Component there are five connections to each device, the red, green, and blue video cables plus the red and white audio cables. 2 1 Cable Box 12 Installation DTV Setup - To watch digitally broadcast programs, purchase and connect a digital set-top box. AC INPUT Y PB PR H/P S-VIDEO VIDEO (MONO) L VIDEO IN AUDIO R PC INPUT ANT IN +75 COMPONENT(480i/480p/720p/1080i) DVD/DTV IN PC SOUND Connections Connect the digital set-top box video outputs to the COMPONENT (Y, PB, PR) jacks and connect the digital set-top box audio outputs to the AUDIO jacks. Viewing Setup Y PB PR (R) AUDIO (L) 1. Turn on the digital set-top box. (Refer to the owner's manual for the digital set-top box.) 2. Use the tv/video or multimedia button on the remote control to select Component. DTV Receiverr (Set-top Box) External A/V Source Setup Connections Connect the audio/video output jacks on the external A/V equipment to the corresponding input jacks on the TV. When connecting the TV to external A/V equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). S-VIDEO VIDEO (MONO) L VIDEO IN AUDIO R PC INPUT ANT IN +75 PC SOUND Camcorder Viewing Setup 1. Turn on the external A/V equipment. 2. Use the tv/video button on the remote control to select Video. 3. Operate the corresponding external equipment. Refer to external equipment operating guide. Video Game set R AUDIO External Equipment L VIDEO DVD Setup Connections 1. Connect the DVD video outputs to the COMPONENT (Y, PB, PR) jacks and connect the DVD audio outputs to the AUDIO jacks. 2. Component Video jacks on other devices may not be labeled the same as they are on this TV, refer to the chart below for a list of other labeling schemes. Component ports of the TV Y Y Y Y Y PB PR · Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below. AC INPUT Y PB PR H/P S-VIDEO VIDEO (MONO) L VIDEO IN AUDIO R PC INPUT ANT IN +75 COMPONENT(480i/480p/720p/1080i) DVD/DTV IN PC SOUND Video output ports of DVD player Pr Pb B-Y R-Y Cr Cb PB PR NOTE: If your DVD player does not have component video output, use S-Video. Viewing Setup 1. Turn on the DVD player, insert a DVD. 2. Use the tv/video or multimedia button on the remote control to select Component (If connected to S-VIDEO, select the SVideo input source.) 3. Refer to the DVD player's manual for operating instructions. Y PB PR (R) AUDIO (L) S-VIDEO (R) AUDIO (L) DVD 13 Installation Using Headphones - Plug headphones in to H/P jack as shown. - Adjust sound level to a headphone using the volume (F, G) buttons. While you are listening to sound through a headphone(s) TV speakers are shut off. AC INPUT Y PB PR H/P S-VIDEO VIDEO (MONO) L VIDEO IN COMPONENT(480i/480p/720p/1080i) DVD/DTV IN PC Setup (Z15LA7R Only) - After setup, be sure to select PC source on TV. Connections 1. Set the monitor output resolution on the PC before connecting to the TV. 2. Connect the TV to the PC with the PC cable. 3. Connect the PC audio output to the TV's PC SOUND input. Viewing Setup 1. Turn on the PC. 2. Use the tv/video or multimedia button on the remote control to select PC. Monitor Display Specifications Resolution Horizontal Vertical Frequency(kHz) Frequency(Hz) 31.47 60 35.00 37.50 35.16 800x600 37.88 48.08 46.88 48.36 1024x768 56.48 60.02 66.67 75 56.25 60 72.19 75 60 70 75 640x480 NOTES a. For optimum picture quality, use standard XGA (1024x768) computer output at a 60Hz refresh rate. Using other formats (VGA, SVGA, etc.) or refresh rates may result in reduced picture quality. (To change the computer video output format, please refer to the operating manual for the computer you are using). b. If the message "Out of range" appears on the screen, adjust the PC output to a format listed in the `Displayable Monitor Output Format Specifications' chart above. c. The synchronization input form for Horizontal and Vertical frequencies is separate. DPM (Display Power Management) mode If the PC goes to power saving mode, the monitor automatically switches to DPM mode. DPM mode may not work if you don't use the PC cable provided. 14 Operation Operation PC Menu Options (Z15LA7R Only) - After setup, be sure to select PC source to see the PC image on TV screen. PC H-Position V-Position Clock Phase Auto Configure Reset 85 D F E OK MENU 1. Press the menu button and then use D 2. Press the 3. Use the F G /E button to select the PC menu. button and then use D /E button to select desired item. / G button to make appropriate adjustments. · H-position/V-position Adjusts picture left/right and up/down. The adjustment ranges of H-Position is 0~100. (Based on the input mode, the adjustment range may change.) · Clock Minimizes any vertical bars or stripes appearing on the screen background. The adjustment range is 0~100. (Based on the input mode, the adjustment range may change.) · Phase Remove any horizontal noise and clear up or sharpen the character images. The range adjustment is 0~100. (Based on the input mode, the adjustment range may change.) · Auto-configure Automatically adjusts the screen position, clock, and clock phase. (The displayed image will disappear for a few seconds while Auto-configuration is in progress.) · Reset Returns to the default settings programmed at the factory; default settings cannot be changed. 4. Press the enter button to save. 15 Operation TV Operation Overview 1. First, make all equipment connections. Plug the AC Adapter into the TV, then plug the AC Adapter into a power outlet. At this time, the TV is switched to standby mode. · In standby mode, press the power, ch (D,E), tv/video, multimedia or a number button on the remote control or on/off, ch (D,E), tv/video located on the TV to turn the TV on. 2. Select the viewing source by pressing tv/video or multimedia repeatedly. · Note: See page 16 if you have not auto programmed the TV to receive channels in your local broadcast area. 3. After viewing, press the power button on the remote control or on/off located on the TV. The TV reverts to standby mode. NOTE · If you want to turn the TV off, press the on/off button located on the TV. If you intend to be away on vacation, disconnect the power plug from the wall power outlet. Menu Language Selection - The menus can be shown on the screen in the selected language. First select your language. 1. Press the menu button and then use 2. Press the G button and then use D / D / E button to select the Special menu. E button to select Language. 3. Press the G button and then use D / E button to select your desired language. From this point on, the on-screen menus will be shown in the language of your choice. 4. Press the exit button to save and return to TV viewing. 16 Operation Channel Menu Options Memorizing the Channels with EZ Scan - For Auto program to work, the programming source must be connected to the TV and the TV must be receiving programming signals either over-the-air or from a cable-type service provider. 1. Press the menu button and then use D / E button to select the Channel menu. 2. Press the G button and then use D /E Channel EZ Scan Manual prog. Favorite ch. To start button to select EZ Scan. 3. Press the G button to begin the channel search. · Wait for auto program to complete the channel search cycle before choosing a channel. The TV scans for over-the-air channels and then channels provided by a cable service. D FG E OK MENU NOTES · When the channel search is complete, use the D / E buttons to review the memorized channels. · If you press the enter button in auto programming, the function will stop and only channels programming up to that time will remain. · Auto program function can memorize only the channels which are being received at that time. Add/Delete Channels with Manual Program - You can manually include or erase individual channels. 1. Press the menu button and then use D / E button to select the Channel menu. 2. Press the G button and then use D /E /G The current channel number is displayed. button to select Manual prog. 3. Press the G button and then use F to add to memory or erase. 4. Press the E button and then use Erase (delete). button to select a channel you want button to select Memory (add) or Channel EZ Scan Manual prog. Favorite ch. TV Memory 30 F /G 5. Press the enter button to save. The current channel is added to Memory or Erased from the channel list. D FG E OK MENU Â EXIT Favorite Channels Setup - Favorite Channel lets you quickly tune in up to 8 channels of your choice without having to wait for the TV to scan through all the in-between channels. Channel EZ Scan Manual prog. Favorite ch. Favorite Ch. ------------------------------------------------------------------------OK MENU Â To set D FG E EXIT D FG E OK MENU /E 1. Press the menu button and then use D 2. Press the G button and then use 3. Press the G button and then use 4. Use the F / G button D /E D button to select the Channel menu. button to select Favorite ch.. / E button to select the first favorite channel position. to set the desired channel number for first favorite channel. 5. Repeat steps 3 to 4 to memorize other channels. 6. Press the enter button to save. · To tune to a favorite channel, press the fcr (Favorite Channel Review) button repeatedly. The 8 favorite channels appear on the screen one-by-one. 17 Operation Picture Menu Options EZ Video Video - This function adjusts the TV for the best picture appearance. 1. Press the video button repeatedly to select the picture appearance setup option as shown below. Clear Optimum Soft User · You can also adjust EZ Video in the Picture menu. · Clear, Optimum and Soft are preset for good picture quality at the factory and cannot be changed. Manual Picture Control (User option) ( - You can adjust picture contrast, brightness, color, sharpness and tint to the levels you prefer. 1. Press the menu button and then use D /E button to select the Picture menu. 2. Press the G button and then use D / E button to select the desired picture option (Contrast, Brightness, Color, Sharpness, Tint). 3. Use the F / G button to make appropriate adjustments. · Contrast, Brightness, Color, and Sharpness are adjustable from 0 to 100. · Tint is adjustable from - 50 to + 50. 4. Press the enter button to save. Picture EZ Video Contrast Brightness Color Sharpness Tint Contrast 85 D FG E OK MENU 18 Operation Sound Menu Options EZ Audio - This function lets you enjoy the best sound without any special adjustment because the TV selects the appropriate sound option based on the program content. 1. Use the audio button to select the appropriate sound setup as shown below. Flat Music Movie Sports User · You can also adjust EZ Audio in the Sound menu. Equalizer Adjustments 1. Press the menu button and then use D / E button to select the Sound menu. 2. Press the G button and then use select EZ Audio. 3. Press the G button and then use select User.