User manual ZENITH Z52DC2D - OPERATING GUIDE

Installation and Operating Guide | Warranty Model Numbers | Z52DC2D/Z56DC1D/Z62DC1D | DLP PROJECTION ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA). As an ENERGY STAR Partner LGE U.S.A., Inc. has determined that this product meets the ENERGY STAR guidelines for energy drriciency. © Copyright 2006, LG Electronics USA, Inc. Warning/Caution WARNING/CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING/CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING/CAUTION: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. POWER CORD POLARIZATION: CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. REGULATORY INFORMATION: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CAUTION: Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user's authority to operate this product. COMPLIANCE: The responsible party for this device compliance is: Zenith Electronics Corporation 1-201-816-2000 Marked and Distributed in the United States by LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 http://www.zenith.com Safety Instructions IMPORTANT SAFETY INSTRUCTIONS Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the apparatus. This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The important safety instructions shall be entitled "Important Safety Instructions". The following safety instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. At the manufacturer's option, a picture or drawing that illustrates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction : 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. PORTABLE CART WARNING Owner's Manual 3 Safety Instructions 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped. 15. CAUTION concerning the Power Cord : Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. 16. Outdoor Use Marking : WARNING - To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Appliance To Rain Or Moisture. 17. Wet Location Marking : Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. R R TruSurround XT is a trademark of SRS Labs, TruSurround XT Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc. Manufactured under license from Dolby Laboratories. "Dolby "and the double-D symbol are trademarks of Dolby Laboratories. High-definition television. High-resolution digital television broadcast and playback system composed of roughly a million or more pixels, 16:9 aspect-ratio screens, and AC3 digital audio. A subset of digital television, HDTV formats include 1080i and 720p resolutions. HDMITM, the HDMI logo and HighDefinition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing." 4 DLP Projection TV Contents Warning/Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4 Audio Menu Options Audio Language . . . . . . . . . . . . . . . . . . . . . . . .32 Auto Volume Leveler (EZ SoundRite) . . . . . . . .32 Auto Sound Control (EZ Sound) . . . . . . . . . . . .32 Manual Sound Control (EZ sound-User Option) .33 Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 TV Speakers On/Off Setup . . . . . . . . . . . . . . . .34 Time Menu Options Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . .35 Manual Clock Setup . . . . . . . . . . . . . . . . . . . . .35 On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .36 Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Option Menu Features Aspect Ratio Control . . . . . . . . . . . . . . . . . . . . .38 Caption / Text . . . . . . . . . . . . . . . . . . . . . . . . . .39 Caption Option Lock Menu Options Parental Lock Setup . . . . . . . . . . . . . . . . . . . . .42 Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 EPG (Electronic Program Guide) (In DTV mode) . . .43 Brief Info. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 Programming the Remote Programming Codes . . . . . . . . . . . . . . . . . . . . . .45 . . . . . . . . . . . . . . . . . . . . . . . .40 Low Power . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 Introduction Controls/Connection Options . . . . . . . . . . . . . .6~9 Remote Control Key Functions . . . . . . . . . 11~12 Installation External Equipment Connections . . . . . . . . . .13~18 Antenna Connection . . . . . . . . . . . . . . . . . . . . .13 VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .14 External A/V Source Setup . . . . . . . . . . . . . . . .15 DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 HDSTB Setup . . . . . . . . . . . . . . . . . . . . . . . . .16 AV Out Setup . . . . . . . . . . . . . . . . . . . . . . . . . .16 Digital Audio Output . . . . . . . . . . . . . . . . . . . . .17 PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . .18~20 Operation Turning the TV On . . . . . . . . . . . . . . . . . . . . . . . .21 TV Setup On-screen Menus Language Selection . . . . . . .22 Channel Selection . . . . . . . . . . . . . . . . . . . . . . .22 Volume Adjustment . . . . . . . . . . . . . . . . . . . . . .22 Setup Menu Options EZ Scan (Channel Search) . . . . . . . . . . . . . . . .23 Manual Scan . . . . . . . . . . . . . . . . . . . . . . . . . .23 Channel Edit . . . . . . . . . . . . . . . . . . . . . . . . . . .24 DTV Signal Input Label . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Input Source Selection . . . . . . . . . . . . . . . . . . .25 . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Video Menu Options Auto Picture Control (EZ Picture) . . . . . . . . . . .26 Adaptive Picture Mode (APM) . . . . . . . . . . . . . .26 Color Temperature Control . . . . . . . . . . . . .27~28 XD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Advanced-Cinema 3:2 Mode / Black Level . . . .30 Video Reset . . . . . . . . . . . . . . . . . . . . . . . . . . .31 . . . . . . . . . . . . . . . . . . . . . . .46~48 Troubleshooting Checklist . . . . . . . . . . . . . . . . . . .49~50 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . .51 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 After reading this manual, keep it handy for future reference. Owner's Manual 5 Controls - This is a representation of the front panel of models Z56DC1D, Z62DC1D series TVs. - Here shown may be somewhat different from your TV. Front Panel Controls INPUT MENU ENTER VOL CH POWER Button INPUT Button ENTER Button CHANNEL (E, E D) Buttons Operation Indicator/ Lamp Indicator/ Temperature Indicator MENU Button FG VOLUME (F,G) Buttons Function Status Indicators - Lamp indicator, operation indicator, and temperature indicator located below the front panel controls, reveal theoperating status of the DLP projection TV. Off Red Green Orange (blinking) Orange Red (blinking) Green (blinking) Orange Temperature Indicator Red Red (blinking) Power Cord is not connected. Power Cord is connected, TV is in standby mode. TV turns on. Preparing operation in standby mode. Projection lamp is reaching the end of its life and needs to be replaced with a new lamp. Contact your service center. There is a problem with the lamp or around it. Contact an authorized service center. The lamp cover is not closed. The projection TV is overheating. Check the blocked vents of the Projection TV . The projection TV shuts down due to overheating. The projection TV shuts down, check the cooling fan. Contact your service center. Operation Indicator Lamp Indicator 6 DLP Projection TV Connection Options - This is the back panel of models Z56DC1D, Z62DC1D series TVs. Back Connection Panel ANTENNA COMPONENT IN 2 1 RGB IN Y VIDEO VIDEO PB AV IN 1 AV OUT RGB (PC/DTV) MONO (L) AUDIO (R) DIGITAL AUDIO OPTICAL OUTPUT PR (L) AUDIO (L) AUDIO RGBDVI (R) S-VIDEO (R) HDMI /DVI IN SERVICE ONLY CABLE IN ANTENNA IN AV IN 1 AC IN AC IN COMPONENT IN 1 2 RGB IN Y CABLE IN ANTENNA IN AV IN 1 AV OUT VIDEO AV OUT COMPONENT IN 1/2 VIDEO PB RGB (PC/DTV) MONO (L) AUDIO (R) DIGITAL AUDIO OPTICAL OUT PR (L) AUDIO (L) AUDIO RGB/DVI (R) S-VIDEO DIGITAL AUDIO OPTICAL OUT (R) SERVICE ONLY SERVICE ONLY HDMI /DVI IN HDMI/DVI IN RGB/DVI AUDIO IN RGB(PC/DTV) VIDEO IN Operating Guide 7 Controls - This is a representation of the front panel of models Z52DC2D series TVs. - Here shown may be somewhat different from your TV. Front Panel Controls INPUT MENU VOL CH POWER Button CHANNEL (E, E D) Buttons Operation Indicator/ Lamp Indicator/ Temperature Indicator INPUT/ENTER Button MENU Button VOLUME (F,G) Buttons FG Function Status Indicators - Lamp indicator, operation indicator, and temperature indicator located below the front panel controls, reveal theoperating status of the DLP projection TV. Off Red Green Orange (blinking) Orange Red (blinking) Green (blinking) Orange Red Red (blinking) Power Cord is not connected. Power Cord is connected, TV is in standby mode. TV turns on. Preparing operation in standby mode. Projection lamp is reaching the end of its life and needs to be replaced with a new lamp. Contact your service center. There is a problem with the lamp or around it. Contact an authorized service center. The lamp cover is not closed. The projection TV is overheating. Check the blocked vents of the Projection TV . The projection TV shuts down due to overheating. The projection TV shuts down, check the cooling fan. Contact your service center. Operation Indicator Lamp Indicator Temperature Indicator 8 DLP Projection TV Connection Options - This is the back panel of models Z52DC2D series TVs. Back Connection Panel CABLE IN ANTENNA IN AV IN 1 AC IN AC IN COMPONENT IN 1 2 RGB IN Y CABLE IN ANTENNA IN AV IN 1 AV OUT VIDEO AV OUT VIDEO PB COMPONENT IN 1/2 RGB (PC/DTV) MONO (L) AUDIO (R) DIGITAL AUDIO OPTICAL OUT PR (L) AUDIO (L) AUDIO RGB/DVI (R) S-VIDEO DIGITAL AUDIO OPTICAL OUT (R) SERVICE ONLY SERVICE ONLY HDMI /DVI IN HDMI/DVI IN RGB/DVI AUDIO IN RGB(PC/DTV) VIDEO IN Owner's Manual 9 Front Connection Panel There are four jacks on the left side on your projection TV that make connecting Audio/Video devices like video games and camcorders very simple. The jacks are like those found on the back jack connection panel. This means that most equipment that connects to those types of jacks on the rear jackpack, may be connect-ed to the front connection panel. To use the side jacks as the signal source, select them using Main Input menu as described on page 25. They will be named "AV 2" in the Main Input menu. Z52DC2D Z56DC1D, Z62DC1D If you input both AV 2 and SVideo, only the S-Video will work. If you're connecting a video game device, make sure to change the picture settings with the EZ Picture option in the Video menu (see page 24). LEFT/RIGHT AUDIO Used for stereo sound from various types of equipment. VIDEO Connects the video signals from any piece of equipment. AV IN 2 / AV IN 2 S-VIDEO A connection available on some very high-end equipment that provides better picture quality than video input. Mini glossary A/V CABLESAudio/Video cables. Three cable connector--Right audio (red), Left audio (white), and Video (yellow). A/V cables are used for stereo playback of videocassettes and for higher quality picture and sound from other A/V devices. A/V DEVICE Any device that produces video or sound (VCR, DVD, cable box, or television). 10 DLP Projection TV Remote Control Key Functions - When using the Remote Control, aim it at the remote control sensor on the TV. MODE Select the remote oper ting mode: TV, VCR, Cable, DVD and SatelliteSelect other operating modes, for theremote to control external devices. TV MODE VCR CABLE DVD SAT LIGHT POWER INDICATOR LIGHTS Show active remote mode every time any button is pressed. INPUT Selects: Antenna, Cable, AV1, AV2, Component1-2, RGB and HDMI/DVI input sources. INPUT RGB-PC TV INPUT TIMER INFO HDMI/DVI LIGHT Illuminates the Remote Control keys. 1 NUMBER KEYPAD For direct channel selection and programming functions. 2 5 8 0 3 6 9 FLASHBK FAV 4 7 MUTE INFO When you watch the TV, information displays on top of the screen. MUTE Switches the sound on or off.(Refer to p.22) FAV Scrolls the Favorite channels. + SAP VOL ADJUST CH VOLUME UP/DOWN Increases/decreases the sound level. EZ SOUND SRS APM EZ PIC ADJUST Adjusts screen position, size, and phase in RGB-DTV/PC or HDMI-PC mode. RATIO Changes the screen format or aspect ratio. RATIO CC FREEZE GUIDE GUIDE Shows program schedule. ENTER MENU Brings up the main menu to the screen. MENU EXIT ENTER When in the menu system and other on-screen displays, selects highlighted options. SKIP Playing CDs: Selects songs. Playing DVDs: Selects movie chapters. EXIT Clears all on-screen displays and returns to TV viewing from any menu. Owner's Manual 11 Remote Control Key Functions POWER Turns your TV or any other programmed equipment on or off, depending on mode. TV INPUT Rotates the input mode between Antenna and Cable. AV1-2, Component 1-2, RGB-DTV (or RGB-PC) and HDMI/DVI input sources, TV will return to the last TV channel. HDMI/DVI RGB-PC Selects the RGB-PC input mode. In other input sources, change to theRGBPC mode. TV MODE VCR CABLE DVD SAT LIGHT POWER INPUT TV INPUT TIMER INFO HDMI/DVI TIMER Lets you select the amount of timebefore your TV turns itself off automatically. RGB-PC 1 4 2 5 8 0 3 6 9 FLASHBK FAV SAP Selects MTS sound: Mono, Stereo, and SAP in Analog mode. Change the audio language in DTV mode. FLASHBK Tunes to the last channel viewed. 7 MUTE + CHANNEL UP/DOWN Scrolls through available channels in EZ Scan memory. EZ SOUND Selects the sound appropriate for the program's character. SAP VOL ADJUST CH EZ SOUND SRS APM EZ PIC EZ PIC Adjusts the factory preset picture depending on the viewing environment. SRS Selects the sound appropriate for the select the desired sound (Off, 3DEchoSound System or SRS TruSurround XT)in Front Surround function. CC Selects a closed caption mode for displaying captioning information if available on program. RATIO CC FREEZE GUIDE APM(ADAPTIVE PICTURE MODE) Concurrently, compare with the Daylight,Normal, Night Time and User1 on the screen. ENTER FREEZE Freezes the currently-viewed picture. MENU EXIT THUMBSTICK Allows you to navigate the on-screen menus and to adjust the system settings and preferences, by moving to an option D withF E G and selecting the highlighted option with . RECORD, PAUSE, REW, FFWD, PLAY, STOP Control the functions on your VCR. Installing Batteries · Open the battery compartment cover on the back side and install the batteries matching correct polarity (+ with +, - with -). · Install two 1.5V AA batteries. Don't mix old or used batteries with new ones. Close cover. 12 DLP Projection TV back of remote External Equipment Connections 1. Analog and Digital TV signals provided on antenna - Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections - For optimum picture quality, adjust antenna direction if needed. Multi-family Dwellings/Apartments (Connect to wall antenna socket) Wall Antenna Socket Bronze Wire ANTENNA IN RF Coaxial Wire (75 ohm) VHF Antenna UHF Antenna Turn clockwise to tighten. Bronze Wire Outdoor Antenna Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna) Be careful not to bend the bronze wire when connecting the antenna. 2. Analog and Digital TV signals provided on cable Cable TV Wall Jack RF Coaxial Wire (75 ohm) CABLE IN Bronze Wire Owner's Manual 13 3. Analog and Digital TV signals provided on cable and antenna Antenna Bronze Wire RF Coaxial Wire (75 ohm) Cable TV Wall Jack Turn clockwise to tighten. CABLE IN ANTENNA IN RF Coaxial Wire (75 ohm) Bronze Wire · To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly. · If the antenna needs to be split for two TV's, install a "2Way Signal Splitter" in the connections. ANTENNA IN Signal Amplifier · If the antenna is not installed properly, contact your dealer for assistance. Note: The TV will let you know when the TV(analog antenna), DTV(digital antenna), CATV(analog cable) and CADTV(digital cable) channel scans are complete. VCR Setup Connection Option 1 Set VCR output switch to channel 3 or 4 and then tune the TV to the same channel number. AC IN CABLE IN ANTENNA IN Connection Option 2 1. Connect the audio and video cables from the VCR's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to VCR, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). If you connect an S-VIDEO output from VCR to the S-VIDEO input, the picture quality is improved; compared to connecting only the Video input. 2. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner's manual.) 3. Select the input source with using the INPUT button on the remote control. Note that this TV finds the connected input sources automatically for AV 1-2 and Component 1-2. COMPONENT IN 1 2 RGB IN Y VIDEO VIDEO PB AV IN 1 AV OUT RGB (PC/DTV) MONO (L) AUDIO (R) DIGITAL AUDIO OPTICAL OUT PR (L) AUDIO (L) AUDIO RGB/DVI (R) S-VIDEO (R) HDMI /DVI IN SERVICE ONLY 1 2 Do not connect to both AV1-2 and S-Video at the same time. In the event that you connect both AV and the S-Video cables, only the S-Video will work. VCR Rear ANT OUT ANT IN S-VIDEO OUT VIDEO (R) AUDIO (L) OUTPUT SWITCH 3 4 IN 14 DLP Projection TV External A/V Source Setup How to connect Connect the audio and video cables from the external equipment's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). AV IN 1 AV OUT VIDEO Camcorder (L) (L) AUDIO (R) DIGITAL AUDIO OPTICAL OUT MONO How to use 1. Select the input source by using the INPUT button on the Remote Control. Note that this TV finds the connected input sources automatically for AV 1-2 and Component 1-2. It is presumed that RGB and HDMI/DVI sources are connected. 2. Operate the corresponding external equipment. (R) Video Game Set S-VIDEO R AUDIO L VIDEO HDMI /DVI IN DVD Setup How to connect 1. Connect the DVD video outputs (Y, PB, PR) to the COMPONENT (Y, PB, PR) INPUT jacks on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure. 2. If your DVD only has an S-Video output jack, connect this to the S-VIDEO input on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure. Note: If your DVD player does not have component video output, use S-Video. ANTENNA G-LINK DIGITAL AUDIO OPTICAL OUT SERVICE RGB IN(PC/DTV) ONLY C a b l e C A R D DIGITAL AUDIO OPTICAL IN 1 (COMPONENT2) CABLE DIGITAL AUDIO OPTICAL IN 2 (DVI) XGA/ 480p/ 720p/ 1080i S-VIDEO COMPONENT IN 2 1 AUDIO IN(RGB/DVI) (L) Y AUDIO (R) PB (L) (MONO) AV OUT AV IN 2 AV IN 1 VIDEO IEEE-1394 IN AUDIO How to use 1. Turn on the DVD player, insert a DVD. 2. Use the INPUT button on the remote control to select Component 1 or Component 2. (If connected to S-VIDEO, select the AV1 or AV2 external input source.) 3. Refer to the DVD player's manual for operating instructions. HDMI IN 1 (DVI) (R) PR VARIABLE AUDIO OUT (L) AUDIO (R) HDMI IN 2 (L) AUDIO (R) · Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below. Component ports on the TV Y Y Y Y Y PB PR or B R (R) AUDIO (L) DIGITAL AUDIO OPTICAL S-VIDEO (R) AUDIO (L) DVD Video output ports on DVD player Pr Pb B-Y R-Y Cb Cr PB PR Owner's Manual 15 HDSTB Setup - This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below. - This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i). How to connect Use the TV's COMPONENT (Y, PB, PR) INPUT, RGB, HDMI/DVI jack for video connections, depending on your set-top box connector. Then, make the corresponding audio connections. Signal Component 1/2 480i Yes 480p Yes How to use 720p Yes 1. Turn on the digital set-top box. (Refer to the owner's manual for the digital 1080i Yes set-top box.) 2. Use INPUT on the Remote Control to select Component 1, Component 2, RGB-DTV or HDMI/DVI source. Note: HDMI(High Definition Multimedia Interface): Input that accepts uncompressed digital signal and multi channel digital audio signal. RGB-DTV,HDMI/DVI No Yes Yes Yes AV Out Setup The TV has a special signal output capability which allows you to hook up a second TV or monitor. AV IN 1 AV OUT VIDEO Connect the second TV or monitor to the TV's AV OUT. See the Operating Manual of the second TV or monitor for further details regarding that device's input settings. Note · Component, RGB-PC/RGB-DTV, HDMI/DVI, DTV input sources cannot be used for AV out. (L) (L) AUDIO (R) DIGITAL AUDIO OPTICAL OUT MONO (R) S-VIDEO S-VIDEO IN (R) AUDIO (L) VIDEO HDMI /DVI IN 16 DLP Projection TV Digital Audio Output Send the TV's audio to external audio equipment (stereo system) via the Digital Audio Output (Optical) port. How to connect 1. Connect one end of an optical cable to the TV Digital Audio (Optical) Out port. 2. Connect the other end of the optical cable to the digital audio (optical) input on the audio equipment. 3. Set the " TV Speaker option - Off" in the AUDIO menu. Refer to page 33. See the external audio equipment instruction manual for operation. C A B L E C A R D AV IN 1 AV OUT VIDEO (L) MONO AUDIO (R) DIGITAL AUDIO OPTICAL OUT S-VIDEO DVI HDMI HDMI /DVI IN Caution: Do not look into the optical output port. Looking at the laser beam may damage your vision. Owner's Manual 17 PC Setup - This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. - The TV perceives 640x480, 60Hz as DTV 480p based on the PC graphic card, change the screen scanning rate for the graphic card accordingly. When supporting RGB How to connect 1. Connect the PC to RGB INPUT port of this TV with a RGB cable. 2. If the PC(or the sound card of the PC) has an analog audio out-put connector, connect the PC's audio output to AUDIO INPUT port located on the right side of RGB INPUT port. COMPONENT IN 1 2 RGB IN Y VIDEO PB RGB (PC/DTV) PR How to use (L) (L) AUDIO RGB/DVI (R) 1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60 Hz. 2. Select RGB-PC input source in main input option of SETUP menu. Once you select RGB-PC in main input option of SETUP menu, INPUT button is also available for this purpose. AUDIO (R) SERVICE ONLY AUDIO RGB-PC OUTPUT When supporting DVI How to connect 1. Connect the PC to HDMI/DVI port of this TV with an HDMIRGB IN AV IN 1 AV OUT VIDEO RGB (PC/DTV) MONO to-DVI cable(not supplied with this product). 2. If the PC(or the sound card of the PC) has an analog audio output connector, connect the PC's audio output to AUDIO INPUT port located on the right side of RGB INPUT port. DIGITAL AUDIO OPTICAL OUT (L) AUDIO (R) (L) AUDIO RGB/DVI (R) S-VIDEO How To Use 1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60Hz. 2. Select HDMI/DVI input source in main input option of SETUP menu. INPUT button is also available for this purpose. HDMI /DVI IN AUDIO DVI-PC OUTPUT - Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or bright ness in PC mode. If noise is present, change the PC output to another resolution, change the refresh rate to another rate, adjust Phase Calibration using the ADJUST button or adjust the brightness and contrast on the VIDEO menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. 18 DLP Projection TV