User manual ZENITH Z52SZ80 - OPERATING GUIDE

Installation and Operating Guide | Warranty Model Numbers | Z44SZ80/Z52SZ80 | DLP PROJECTION © Copyright 2005, LG Electronics USA, Inc. Warning/Caution Warning/Caution WARNING/CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING/CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING/CAUTION: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. POWER CORD POLARIZATION: CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. REGULATORY INFORMATION: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CAUTION: Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user's authority to operate this product. COMPLIANCE: The responsible party for this product's compliance is: Zenith Electronics Corporation 1-201-816-2000 Marked and Distributed in the United States by LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 http://www.zenith.com 2 DLP Projection TV Safety Instructions Safety Instructions IMPORTANT SAFETY INSTRUCTIONS Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the apparatus. This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The important safety instructions shall be entitled "Important Safety Instructions". The following safety instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. At the manufacturer's option, a picture or drawing that illustrates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction : 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. PORTABLE CART WARNING Owner's Manual 3 Safety Instructions 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped. 15. CAUTION concerning the Power Cord : Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. 16. Outdoor Use Marking : WARNING - To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Appliance To Rain Or Moisture. 17. Wet Location : Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. 4 DLP Projection TV Contents Contents Warnings/Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4 Introduction Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Connection Options . . . . . . . . . . . . . . . . . . . .7~8 Remote Control Key Functions . . . . . . . . . . .9~10 Installation External Equipment Connections . . . . . . . . . .11~16 Antenna or Cable Connection . . . . . . . . . . . . . .11 VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .12 External A/V Source Setup . . . . . . . . . . . . . . . .13 DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 HDSTB Setup . . . . . . . . . . . . . . . . . . . . . . . . . .14 Monitor Out Setup . . . . . . . . . . . . . . . . . . . . . .14 PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Digital Audio Output . . . . . . . . . . . . . . . . . . . . .16 External Stereo . . . . . . . . . . . . . . . . . . . . . . . . .16 HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17~19 Option Menu Options Aspect Ratio Control . . . Cinema 3:2 Mode Setup Caption . . . . . . . . . . . . . Caption / Text . . . . . . . . Caption Option . . . . . . . EZ Demo . . . . . . . . . . . Lock Menu Options Parental Lock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 .29 .30 .30 .31 .31 . . . . . . . . . . . . . . . . . .33 Operation Turning the TV On . . . . . . . . . . . . . . . . . . . . . .20 TV Setup On-screen Menus Language Selection . . . . . . .21 Setup Menu Options EZ Scan (Channel Search) . . . . . . . . . . . . . . . .22 Channel Edit . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Channel Label Setup . . . . . . . . . . . . . . . . . . . .23 Main Picture Source Selection . . . . . . . . . . . . .23 Input Label . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Video Menu Options EZ Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Manual Picture Control (Custom Option) . . . . . .24 Color Temperature Control . . . . . . . . . . . . . . . .24 Video Reset . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Audio Menu Options Audio Language . . . . . . . . . . . . . . . . . . . . . . . .25 EZ SoundRite / EZ Sound . . . . . . . . . . . . . . . . .25 Manual Sound Control (Custom Option) . . . . . .25 Front Surround . . . . . . . . . . . . . . . . . . . . . . . . .26 TV Speakers On/Off Setup . . . . . . . . . . . . . . . .26 Stereo/SAP Broadcasts Setup . . . . . . . . . . . . . .26 Time Menu Options Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . .27 Manual Clock Setup . . . . . . . . . . . . . . . . . . . . .27 On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .27 Sleep Timer / Auto Off . . . . . . . . . . . . . . . . . . . .28 Remote Control PIP (Picture-in-Picture)/Twin Picture . . . . . . . . ..34 Watching PIP/Twin Picture . . . . . . . . . . . . . . . ..34 Selecting an Input Signal Source for PIP/Twin Picture . .34 Swapping the PIP/Twin Picture . . . . . . . . . . . . .34 TV Program Selection for PIP . . . . . . . . . . . . . .34 Moving the PIP sub picture . . . . . . . . . . . . . . . .35 Adjusting Main and Sub Picture Sizes for Twin Picture . .35 Brief Info.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 EZ Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Screen Setup for PC mode . . . . . . . . . . . . . . . .38 Programming the Remote Programming Codes . . . . . . . . . . . . . . . . . . . . . .39 . . . . . . . . . . . . . . . . . . . . . . .40~42 Troubleshooting Checklist . . . . . . . . . . . . . . . . . . .43~44 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . .46 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 After reading this manual, keep it handy for future reference. Owner's Manual 5 Introduction Introduction Controls - This is a simplified representation of a front panel. - Image shown may be somewhat different from your TV. Front Panel Controls POWER MENU ENTER VOL CH POWER Button MENU Button VOLUME (F,G) Buttons CHANNEL (E, Buttons ENTER Button D) Operation Indicator/ Lamp Indicator/ Temperature Indicator Function Status Indicators - Lamp indicator, operation indicator, and temperature indicator located below the front panel controls, reveal the operating status of the DLP projection TV. Off Red Green Orange (blinking) Orange Red (blinking) Green (blinking) Orange Temperature Indicator Red Red (blinking) Power cord is not connected. Power Cord is connected, TV is in standby mode. TV turns on. Preparing operation in standby mode. Projection lamp is reaching the end of its life and needs to be replaced with a new lamp. Contact your service center. There is a problem with the lamp or around it. Contact an authorized service center. The lamp cover is not closed. The projection TV is overheating. Check for blocked vents on the projection TV. The projection TV shut down due to overheating. The projection TV shut down, check the cooling fan. Contact your service center. Operation Indicator Lamp Indicator 6 DLP Projection TV Introduction Connection Options Back Connection Panel DIGITAL AUDIO OPTICAL OUTPUT Used to connect either an external amplifier, or add a sub-woofer to your surround sound system if it has a digital audio optical input. (Refer to 1 ) DIGITAL AUDIO OPTICAL INPUT(COMPONENT2) Connect digital audio from the equipment connected to COMPONENT 2. DIGITAL AUDIO OPTICAL INPUT(DVI) Connect digital audio from the equipment connected to HDMI/DVI(VIDEO). HDMI1/DVI, HDMI 2 Connect a HDMI signal to HDMI1/DVI or HDMI2. Or connect a DVI(Video) signal to HDMI1/DVI. CABLE Inputs ANTENNA Inputs Connect cable signals to Connect antenna sigthe TV, either directly or nals to the TV directly. through your cable box. ANTENNA RGB Input Connect the TV output connector from a PC/DTV to the appropriate input port. S-VIDEO In A connection available with some highend equipment that provides even better picture quality for Video 2. DIGITAL AUDIO OPTICAL OUTPUT CABLE DIGITAL AUDIO OPTICAL INPUT (COMPONENT2) RGB INPUT PC/DTV (XGA/ 480p/ 720p/ 1080i) RGB/DVI INPUT S-VIDEO DIGITAL AUDIO OPTICAL INPUT (DVI) COMPONENT INPUT2 INPUT1 MONITOR INPUT2 OUT INPUT1 VIDEO H D M I 1 H D M I 2 / D V I Y (L) PB AUDIO (R) PR MONO VIDEO 1 or 2 Connects the video signals from various types of equipment. Left/Right AUDIO Used for stereo sound from various types of equipment. (L) AUDIO (R) VARIABLE AUDIO OUT (L) AUDIO (R) DTV/DVD INPUT UPGRADE PORT (L) AUDIO (R) MONITOR OUT Connect a second TV or Monitor. VARIABLE AUDIO OUT Used to connect either an external amplifier, or add a sub-woofer to your surround sound system. COMPONENT INPUT 1-2 Connect a component video/audio device to these jacks. Refer to your DVD manual for further information. RGB/DVI INPUT Connect the monitor output connector from a PC to the appropriate input port. Note: 1 In standby mode, these port will not work. Owner's Manual 7 Introduction Front Connection Panel There are four jacks on the left side on your projection TV that make connecting Audio/Video devices like video games and camcorders very simple. The jacks are like those found on the back jack connection panel. This means that most equipment that connects to those types of jacks on the rear jackpack, may be connected to the front connection panel. To use the side jacks as the signal source, select them using Main Input menu as described on page 23. They will be named "Front Video" in the Main Input menu. If you input both Front Video and S-Video, only the S-Video will work. Front A/V Panel If you're connecting a video game device, make sure to change the picture settings with the EZ Picture option in the Video menu (see page 24). LEFT/RIGHT AUDIO Used for stereo sound from various types of equipment. VIDEO Connects the video signals from any piece of equipment. (R) AUDIO (L)/ MONO VIDEO S-VIDEO S-VIDEO FRONT A/V A connection available on some very highend equipment that provides better picture quality than video input. Mini glossary A/V CABLESAudio/Video cables. Three cable connector--Right audio (red), Left audio (white), and Video (yellow). A/V cables are used for stereo playback of videocassettes and for higher quality picture and sound from other A/V devices. A/V DEVICE Any device that produces video or sound (VCR, DVD, cable box, or television). 8 DLP Projection TV Introduction Remote Control Key Functions - When using the Remote Control, aim it at the remote control sensor on the TV. MODE Selects the remote operating mode: TV, VCR, Cable, DVD and Satellite. Select other operating modes, for the remote to control external devices. TV MODE VCR CABLE DVD SAT LIGHT POWER INDICATOR LIGHTS Show active remote mode every time any button is pressed. TV/VIDEO Selects: Analog, Video1, Video2, Front video, Component1-2, RGB, HDMI1/DVI and HDMI2 input sources. TV/VIDEO TV INPUT EZ Video EZ Sound INFO SLEEP LIGHT Illuminates the Remote Control keys. 1 NUMBER KEYPAD For direct channel selection and programming functions. 2 5 8 0 3 6 9 FLASHBK FAV 4 7 INFO When you watch the TV, information displays on top of the screen. Not available in Component 1-2, RGB, HDMI1/DVI and HDMI2 mode.(Refer to p.36) MUTE Switches the sound on or off.(Refer to p.37) MUTE + SAP VOL FAV Scrolls the Favorite channels. ADJUST CH VOLUME UP/DOWN Increases/decreases the sound level. PIP PIPCH- PIPCH+ SWAP ADJUST Adjusts screen position, size, and phase in RGB-DTV/PC mode. RATIO Changes the screen format or aspect ratio. RATIO CC FREEZE PIP INPUT PIP INPUT Selects the input source for the sub picture. MENU Brings up the main menu to the screen. MENU EXIT ENTER When in the menu system and other on-screen displays, selects highlighted options. PLAY PAUSE STOP RECORD SKIP Playing CDs: Selects songs. Playing DVDs: Selects movie chapters. REW FF SKIP EXIT Clears all on-screen displays and returns to TV viewing from any menu. Owner's Manual 9 Introduction Remote Control Key Functions TV INPUT · Rotates the input mode between Antenna and Cable. · Video 1-2, Front Video, Component 1-2, RGB-DTV (or RGB-PC), HDMI1/DVI and HDMI2 input sources, TV will return to the last TV channel. EZ Video Adjusts the factory preset picture depending on the viewing environment. TV MODE VCR CABLE DVD SAT LIGHT POWER POWER Turns your TV or any other programmed equipment on or off, depending on mode. TV/VIDEO TV INPUT EZ Video EZ Sound INFO SLEEP SLEEP 1 EZ Sound Selects the sound appropriate for the program's character. 2 5 8 0 3 6 9 FLASHBK FAV 4 7 MUTE FLASHBK Tunes to the last channel viewed. SAP Selects MTS sound: Mono, Stereo, and SAP in Analog mode. Change the audio language in DTV mode. CHANNEL UP/DOWN Scrolls through available channels in EZ Scan memory. + SAP VOL ADJUST CH PIP PIPCH- PIPCH+ SWAP SWAP Exchanges the main/sub images in PIP/Twin picture mode. PIP Toggles between PIP and Twin picture mode. RATIO CC FREEZE PIP INPUT PIPCH+ Changes to next higher PIP channel. PIPCHChanges to next lower PIP channel FREEZE Freezes the currently-viewed picture. Main picture is frozen in PIP/Twin picture mode. MENU EXIT CC Selects a closed caption mode for displaying captioning information if available on program. PLAY PAUSE STOP RECORD THUMBSTICK Allows you to navigate the on-screen menus and to adjust the system settings and preferences, by moving to an option D withF E G and selecting the highlighted option with . REW FF SKIP RECORD, PAUSE, REW, FFWD, PLAY, STOP Control the functions on your VCR. Installing Batteries · Open the battery compartment cover on the back side and install the batteries matching correct polarity (+ with +, - with -). · Install two 1.5V AA batteries. Don't mix old or used batteries with new ones. Close cover. back of remote 10 DLP Projection TV Installation Installation External Equipment Connections Antenna or Cable Connection 1. Analog and Digital TV signals provided on antenna - Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections - For optimum picture quality, adjust antenna direction if needed. Multi-family Dwellings/Apartments (Connect to wall antenna socket) Wall Antenna Socket Copper Wire ANTENNA RF Coaxial Wire (75 ohm) VHF Antenna UHF Antenna Turn clockwise to tighten. Copper Wire Outdoor Antenna Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna) Be careful not to bend the Copper Wire when connecting the antenna. 2. Analog and Digital TV signals provided on cable Turn clockwise to tighten. Cable TV Wall Jack RF Coaxial Wire (75 ohm) CABLE Copper Wire Owner's Manual 11 Installation 3. Analog and Digital TV signals provided on cable and antenna Antenna Copper Wire RF Coaxial Wire (75 ohm) ANTENNA Cable TV Wall Jack Turn clockwise to tighten. RF Coaxial Wire (75 ohm) CABLE Copper Wire · To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly. ANTENNA · If the antenna needs to be split for two TV's, install a "2Way Signal Splitter" in the connections. · If the antenna is not installed properly, contact your dealer for assistance. Signal Amplifier Note: The TV will let you know when the TV(analog antenna), DTV(digital antenna), CATV(analog cable) and CADTV(digital cable) channel scans are complete. VCR Setup Connection Option 1 Set VCR output switch to channel 3 or 4 and then tune the TV to the same channel number. ANTENNA Connection Option 2 1. Connect the audio and video cables from the VCR's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to VCR, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). If you connect an S-VIDEO output from VCR to the S-VIDEO input, the picture quality is improved; compared to connecting only the Video input. 2. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner's manual.) 3. Select the input source with using the TV/VIDEO button on the remote control. Note that this TV finds the connected input sources automatically for Video1-2, Front Video and Component 1-2. It is presumed that RGB, HDMI1/DVI and HDMI2 sources are connected. Do not connect to both Video1,2 and S-Video at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work. DIGITAL AUDIO OPTICAL OUTPUT CABLE DIGITAL AUDIO OPTICAL INPUT (COMPONENT2) RGB INPUT PC/DTV (XGA/ 480p/ 720p/ 1080i) RGB/DVI INPUT S-VIDEO DIGITAL AUDIO OPTICAL INPUT (DVI) COMPONENT INPUT2 INPUT1 MONITOR INPUT2 OUT INPUT1 VIDEO H / D D M V I I 1 H D M I 2 Y (L) PB AUDIO (R) PR MONO (L) AUDIO (R) VARIABLE AUDIO OUT (L) AUDIO (R) DTV/DVD INPUT UPGRADE PORT (L) AUDIO (R) 1 2 ANT OUT ANT IN S-VIDEO OUT (R) AUDIO (L) VCR Rear VIDEO OUTPUT SWITCH 3 4 IN 12 DLP Projection TV Installation External A/V Source Setup How to connect Connect the audio and video cables from the external equipment's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). RGB INPUT PC/DTV (XGA/ 480p/ 720p/ 1080i) RGB/DVI INPUT S-VIDEO MONITOR INPUT2 OUT INPUT1 VIDEO VIDEO Camcorder How to use 1. Select the input source by using the TV/VIDEO button on the Remote Control. Note that this TV finds the connected input sources automatically for Video 1-2 and Component 12. It is presumed that RGB, HDMI1/DVI and HDMI2 sources are connected. 2. Operate the corresponding external equipment. (L) AUDIO (R) MONO (L)(L) AUDIO (R) (R) VARIABLE AUDIO OUT (L) AUDIO (R) Video Game Set R AUDIO L VIDEO DVD Setup How to connect 1. Connect the DVD video outputs (Y, PB, PR) to the COMPONENT (Y, PB, PR) INPUT jacks on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure. 2. If your DVD only has an S-Video output jack, connect this to the S-VIDEO input on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure. Note: If your DVD player does not have component video output, use S-Video. ANTENNA DIGITAL AUDIO OPTICAL OUTPUT CABLE DIGITAL AUDIO OPTICAL INPUT (COMPONENT2) RGB INPUT PC/DTV (XGA/ 480p/ 720p/ 1080i) S-VIDEO DIGITAL AUDIO OPTICAL INPUT (DVI) COMPONENT INPUT2 INPUT1 RGB/DVI INPUT H / D D M V I I 1 H D M I 2 MONITOR INPUT2 OUT INPUT1 VIDEO Y (L) PB AUDIO (R) PR MONO (L) AUDIO (R) How to use 1. Turn on the DVD player, insert a DVD. 2. Use the TV/VIDEO button on the Remote Control to select Component 1 or Component 2. (If connected to S-VIDEO, select the Video2 or Front Video external input source.) 3. Refer to the DVD player's manual for operating instructions. VARIABLE AUDIO OUT (L) AUDIO (R) DTV/DVD INPUT UPGRADE PORT (L) AUDIO (R) · Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below. Component ports on the TV Y Y Y Y Y PB PR B R (R) AUDIO (L) DIGITAL AUDIO OPTICAL or S-VIDEO (R) AUDIO (L) DVD Notes: · Digital Audio will not work for Component 1 input source. · Digital Audio operation has priority if Digital Audio and AUDIO L/R are connected at the same time. Video output ports on DVD player Pr Pb B-Y R-Y Cb Cr PB PR Owner's Manual 13 Installation HDSTB Setup - This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below. - This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i). How to connect Use the TV's COMPONENT (Y, PB, PR) INPUT, RGB, HDMI1/DVI or HDMI2 jack for video connections, depending on your set-top box connector. Then, make the corresponding audio connections. Note: HDMI(High Definition Multimedia Interface): Input that accepts uncompressed digital signal and multi channel digital audio signal. Signal Component 1/2 RGB-DTV,HDMI1/DVI,HDMI2 Yes No 480i Yes Yes 480p How to use 720p Yes Yes 1. Turn on the digital set-top box. (Refer to the owner's manual for the digital 1080i Yes Yes set-top box.) 2. Use TV/VIDEO on the Remote Control to select Component 1, Component 2, RGB-DTV, HDMI1/DVI or HDMI2 source. Monitor Out Setup The TV has a special signal output capability which allows you to hook up a second TV or monitor. Connect the second TV or monitor to the TV's MONITOR OUTPUT. See the Operating Manual of the second TV or monitor for further details regarding that device's input settings. Note · Component, RGB-PC/RGB-DTV, HDMI1/DVI,HDMI2, DTV input sources cannot be used for Monitor out. RGB INPUT PC/DTV (XGA/ 480p/ 720p/ 1080i) RGB/DVI INPUT (L) AUDIO (R) S-VIDEO MONITOR INPUT2 OUT INPUT1 MONO VARIABLE AUDIO OUT (L) AUDIO (R) S-VIDEO IN (R) AUDIO (L) VIDEO 14 DLP Projection TV Installation PC Setup - This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. - The TV perceives 640x480, 60Hz as DTV 480p based on the PC graphic card, change the screen scanning rate for the graphic card accordingly. How to connect 1. Connect the PC to HDMI1/DVI port of this TV with an HDMI-to-DVI cable(not supplied with this product). If you do not need to connect audio, HDMI2 port is also available for the DVI video connection. 2. If the PC(or the sound card of the PC) has a fiber optic digital audio output connector, connect the PC's audio output to DIGITAL AUDIO(OPTICAL) port for DVI INPUT. 3. If the PC(or the sound card of the PC) has an analog audio output connector, connect the PC's audio output to AUDIO INPUT port located on the right side of RGB INPUT port. How To Use 1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60Hz. 2. Select HDMI1/DVI input source in main input option of SETUP menu.(Refer to P.23) TV/VIDEO button is also available for this purpose. 3. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the VIDEO menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. How to connect 1. Connect the PC to RGB INPUT port of this TV with a RGB cable. 2. If the PC(or the sound card of the PC) has an analog audio output connector, connect the PC's audio output to AUDIO INPUT port located on the right side of RGB INPUT port. How To Use 1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60 Hz. 2. Select RGB-PC input source in main input option of SETUP menu.(Refer to P.23) Once you select RGB-PC in main input option of SETUP menu, TV/VIDEO button is also available for this purpose. 3. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the VIDEO menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. Monitor Display Specifications (RGB-PC or HDMI1/DVI Mode) Resolution 640x350 Horizontal Frequency(KHz) 31.468 31.469 640x480 37.861 37.500 35.156 37.879 800x600 48.077 46.875 48.363 1024x768 56.476 60.023 Vertical Frequency(Hz) 70.09 59.94 72.80 75.00 56.25 60.31 72.18 75.00 60.00 70.06 75.02 RGB-PC Mode Only Owner's Manual 15 Installation Digital Audio Output Send the TV's audio to external audio equipment (stereo system) via the Digital Audio Output (Optical) port. C A B L E C A R D ANTENNA DIGITAL AUDIO OPTICAL OUTPUT CABLE DIGITAL AUDIO OPTICAL INPUT (COMPONENT2) How to connect 1. Connect one end of an optical cable to the TV Digital Audio (Optical) Output port. 2. Connect the other end of the optical cable to the digital audio (optical) input on the audio equipment. 3. Set the " TV Speaker option - Off" in the AUDIO menu. Refer to page 26. See the external audio equipment instruction manual for operation. Caution: Do not look into the optical output port. Looking at the light may damage your vision. DIGITAL AUDIO OPTICAL INPUT (DVI) COMPONENT INPUT2 INPUT1 DVI H D M I 1 H D M I 2 / D V I Y PB PR HDMI UPGRADE PORT (L) AUDIO (R) DTV/DVD INPUT External Stereo Hook up Variable Audio Output, L-Audio-R to Amplifier system for Left/Right front speaker sound. S-VIDEO RGB INPUT PC/DTV (XGA/ 480p/ 720p/ 1080i) RGB/DVI INPUT (L) AUDIO (R) How to connect MONITOR INPUT2 OUT INPUT1 MONO VARIABLE AUDIO OUT (L) AUDIO (R) 1. Locate the Variable Audio Out jacks on the back of your TV and the Input jacks on the back of your stereo's amplifier. 2. Connect the two jacks, making sure that the right and left channels are connected correctly. 3. Set up your speakers through your analog stereo amplifier, according to the instructions provided with the amplifier. 16 DLP Projection TV Installation HDMI - HDMITM, the HDMI logo and High-Definition Multimedia Interface is a trademark or registered trademark of HDMI Licensing. - This TV can receive the High-Definition Multimedia Interface(HDMI) or the Digital Visual Interface(DVI). - This TV supports HDCP(High-bandwidth Digital Contents Protection) Protocol for 720x480p, 1280x720p, and 1920x1080i resolutions. - When you connect this TV with a source device(DVD player, Set Top Box or PC) supporting Auto HDMI/DVI function, the output resolution of the source device will be automatically set to 1280x720p. - If the source device does not support Auto HDMI/DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the DVD Player or Set Top Box's output resolution to 1280x720p, and the PC graphics card's output resolution to 1024x768, 60Hz. - If the source device has an HDMI output, no other audio connection is necessary because HDMI-to-HDMI connection includes both video and audio. - If the source device has a DVI output and no HDMI output, a separated audio connection is necessary. How To Connect 1. Connect the source device to HDMI1/DVI or HDMI2 port of this TV with an HDMI cable(not supplied with this product). 2. No separated audio connection is necessary. How To Use - If the source device supports Auto HDMI function, the output resolution of the source device will be automatically set to 1280x720p. - If the source device does not support Auto HDMI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the source device to 1280x720p. - Select HDMI1/DVI or HDMI2 input source in main input option on the SETUP menu.(Refer to P.23) TV/VIDEO button is also available for this purpose. How To Connect 1. Connect the source device to HDMI1/DVI port of this TV with a HDMI-to-DVI cable(not supplied with this product). Do not use HDMI2 port for DVI connection if you want to connect audio. 2. A separated audio connection is necessary. 3. If the source device has a fiber optic digital audio output, connect the audio output to DIGITAL AUDIO(OPTICAL) port for DVI INPUT. 4. Connect the PC's audio output to AUDIO INPUT port located on the right side of RGB INPUT port. How To Use - If the source device supports Auto DVI function, the output resolution of the source device will be automatically set to 1280x720p. - If the source device does not support Auto DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the source device to 1280x720p. - Select HDMI1/DVI input source in main input option on the SETUP menu.(Refer to P.23) TV/VIDEO button is also available for this purpose. Owner's Manual 17 Installation Reference Cable sample HDMI Cable (not supplied with the product) HDMI to DVI Cable (not supplied with the product) Fiber Optic Digital Audio Cable (not supplied with the product) Analog Audio Cable(RCA type) (not supplied with the product) Analog Audio Cable(Stereo to RCA type) (not supplied with the product) 18 DLP Projection TV Installation How to use 1. Connect the HDMI1/DVI Source Devices(DVD Player or Set Top Box or PC) and the TV SET. 2. Turn on the display by pressing the POWER button on the TV SET and HDMI1/DVI Source Devices remote control. 3. Select HDMI1/DVI Input source in Main Input option on the SETUP menu.(Refer to P.23) 4. Check the image on your TV SET. There may be noise associated with the resolution, vertical pattern, contrast or brightness in HDMI1/DVI Source Devices. If noise is present, change the HDMI1/DVI Source Devices to another resolution, change the refresh rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphics card can not changed, change the PC graphics card or consult the manufacturer of the PC graphics card. Notes: - Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use. - When Source Devices connected with HDMI1/DVI Input, output TV SET Resolution(480p, 720p, 1080i) and TV SET Display fit EIA/CEA-861-B Specification to Screen. If not, refer to the Manual of HDMI1/DVI Source Devices or contact your service center. - In case HDMI1/DVI Source Devices is not connected Cable or poor cable connection, "NO SIGNAL" OSD display in HDMI1/DVI Input. In case that Video Resolution is not supported TV SET output in HDMI1/DVI Source Devices, "INVALID FORMAT" OSD display. Refer to the Manual of HDMI1/DVI Source Devices or contact your service center. In DTV Mode, the Supported TV Set Resolution Specification 1920 x 1080 I @ 59.94Hz / 60Hz, 16:9 1280 x 720 P @ 59.94Hz / 60Hz, 16:9(preferred format) 720 x 480 P @ 59.94Hz / 60Hz, 16:9 720 x 480 P @ 59.94Hz / 60Hz, 4:3 In PC Mode, the Supported PC Resolution Specification 640 x 480 @ 60Hz 640 x 480 @ 72Hz 640 x 480 @ 75Hz 800 x 600 @ 56Hz 800 x 600 @ 60Hz 800 x 600 @ 72Hz 800 x 600 @ 75Hz 1024 x 768 @ 60Hz(preferred format) 1024 x 768 @ 70Hz 1024 x 768 @ 75Hz Owner's Manual 19 Operation Operation Turning the TV On * In this manual, the OSD (On Screen Display) may be different from your TV's because it is just an example to help you with the TV operation. Turning on the TV just after installation 1. Connect power cord correctly. At this moment, the TV is switched to standby mode. 2. Press the POWER or CH (D / E) buttons on the TV front panel or press the POWER, TV/VIDEO, TV INPUT, CH (D / E) or Number (0 ~ 9) buttons on the Remote Control to turn the TV on.