User manual ZOOM B2.1U

Operation Manual © ZOOM Corporation Reproduction of this manual, in whole or in part, by any means, is prohibited. SAFETY PRECAUTIONS / Usage Precautions Handling SAFETY PRECAUTIONS In this manual, symbols are used to highlight warnings and cautions for you to read so that accidents can be prevented. The meanings of these symbols are as follows: This symbol indicates explanations about extremely dangerous matters. If users ignore this symbol and Warning handle the device the wrong way, serious injury or death could result. This symbol indicates explanations about dangerous matters. If users ignore this symbol and handle the device the wrong way, bodily injury and damage to the equipment could result. Warning · Never place objects filled with liquids, such as vases, on the B2.1u since this can cause electric shock. · Do not place naked flame sources, such as lighted candles, on the B2.1u since this can cause fire. · The B2.1u is a precision instrument. Do not exert undue pressure on the keys and other controls. Also take care not to drop the unit, and do not subject it to shock or excessive pressure. · Take care that no foreign objects (coins or pins etc.) or liquids can enter the unit. Caution Connecting cables and input and output jacks You should always turn off the power to the B2.1u and all other equipment before connecting or disconnecting any cables. Also make sure to disconnect all connection cables and the power cord before moving the B2.1u. Caution Please observe the following safety tips and precautions to ensure hazard-free use of the B2.1u. Alterations Warning Power requirements Warning Since power consumption of this unit is fairly high, we recommend the use of an AC adapter whenever possible. When powering the unit from batteries, use only alkaline types. [AC adapter operation] · Be sure to use only an AC adapter which supplies 9 V DC, 300 mA and is equipped with a "center minus" plug (Zoom AD-0006). The use of an adapter other than the specified type may damage the unit and pose a safety hazard. · Connect the AC adapter only to an AC outlet that supplies the rated voltage required by the adapter. · When disconnecting the AC adapter from the AC outlet, always grasp the adapter itself and do not pull at the cable. · During lightning or when not using the unit for an extended period, disconnect the AC adapter from the AC outlet. Never open the case of the B2.1u or attempt to modify the product in any way since this can result in damage to the unit. Volume Caution Do not use the B2.1u at a loud volume for a long time since this can cause hearing impairment. Usage Precautions Electrical interference For safety considerations, the B2.1u has been designed to provide maximum protection against the emission of electromagnetic radiation from inside the device, and protection from external interference. However, equipment that is very susceptible to interference or that emits powerful electromagnetic waves should not be placed near the B2.1u, as the possibility of interference cannot be ruled out entirely. With any type of digital control device, the B2.1u included, electromagnetic interference can cause malfunctioning and can corrupt or destroy data. Care should be taken to minimize the risk of damage. [Battery operation] · Use four conventional IEC R6 (size AA) batteries (alkaline). · The B2.1u cannot be used for recharging. · Pay close attention to the labelling of the battery to make sure you choose the correct type. · When not using the unit for an extended period, remove the batteries from the unit. · If battery leakage has occurred, wipe the battery compartment and the battery terminals carefully to remove all remnants of battery fluid. · While using the unit, the battery compartment cover should be closed. Cleaning Use a soft, dry cloth to clean the B2.1u. If necessary, slightly moisten the cloth. Do not use abrasive cleanser, wax, or solvents (such as paint thinner or cleaning alcohol), since these may dull the finish or damage the surface. Environment Warning To prevent the risk of fire, electric shock or malfunction, avoid using your B2.1u in environments where it will be exposed to: · · · · · Extreme temperatures Heat sources such as radiators or stoves High humidity or moisture Excessive dust or sand Excessive vibration or shock Please keep this manual in a convenient place for future reference. * Windows and Windows XP are registered trademarks of Microsoft Corporation. * Macintosh is a registered trademark of Apple Computer. * All other product names, trademarks, and company names mentioned in this manual are the property of their respective owners. 2 ZOOM B2.1u Contents SAFETY PRECAUTIONS / Usage Precautions ................................ 2 SAFETY PRECAUTIONS .................................................................... 2 Usage Precautions .............................................................................. 2 Features .............................................................................................. 4 Terms Used in This Manual .............................................................. 5 Controls and Functions / Connections ........................................... 6 Selecting a Patch ............................................................................... 8 Using the Tuner ............................................................................... 10 Using the Rhythm Function ............................................................ 12 Editing a Patch ................................................................................. 14 Storing/Copying Patches ............................................................... 16 Using the Built-in Expression Pedal ............................................... 18 Other Functions................................................................................ 20 Making settings for the internal expression pedal .......................... 20 Adjusting the sensitivity of the built-in expression pedal ............... 20 Using an external expression pedal (FP01/FP02)............................ 21 Using a foot switch (FS01) ................................................................ 21 Using the B2.1u as audio interface for a computer......................... 22 Use as a direct box ........................................................................... 23 Restoring Factory Defaults ............................................................ 24 Linking Effects.................................................................................. 25 Effect Types and Parameters.......................................................... 26 How to read the parameter table ..................................................... 26 COMP/LIMIT ................................................................................. 27 WAH/EFX ...................................................................................... 27 DRIVE/SYNTH ............................................................................... 29 ZNR/MIX ....................................................................................... 30 LO EQ ........................................................................................... 30 HI EQ............................................................................................. 31 MOD/SFX ...................................................................................... 31 DELAY ........................................................................................... 33 REVERB ........................................................................................ 33 CONTROL..................................................................................... 34 Specifications .................................................................................. 35 Troubleshooting .............................................................................. 35 B2.1u Preset Pattern ............................................................ Back cover The FCC regulation warning (for U.S.A.) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. ZOOM B2.1u 3 Features Thank you for selecting the ZOOM B2.1u (hereafter simply called the "B2.1u"). The B2.1u is a multi effect processor with the following features and functions. Latest technology for outstanding performance 96 kHz / 24 bit sampling (with 32 bit internal processing) assures excellent sound quality. The B2.1u carves out a sonic outline in superb detail while preserving the original sound character of the bass guitar. The B2.1u also has a USB connection and can be used as a direct bass guitar/computer interface. Versatile palette of effects Out of a total of 47 effects, up to nine (including ZNR) can be used simultaneously. The dazzling choices provided by the B2.1u include distortion effects modeled on famous amps and compact effects, compressor/ limiter effects for dynamic punch, a parametric equalizer essential for working on sonic nuances, as well as various delay and modulation effects. Both in quality and versatility, the B2.1u far surpasses anything in its class. You can even transform the output into a cool synth bass or fretless bass sound. Really usable patches straight out of the box Effect module combinations are stored and called up in units referred to as patches. The B2.1u comes with a full complement of 40 read-only plus 40 user-programmable patches, giving you 80 great reasons to start grooving. Great for live performances and direct recording The distortion effects have a special parameter that selects whether to apply only the head amp characteristics or add also the cabinet sound. This lets you use the B2.1u effectively not only for a live performance but also when feeding the signal directly to a recorder. XLR connector for direct output In addition to the [OUTPUT/PHONES] jack, the B2.1u features an XLR connector for sending a balanced line-level signal to equipment such as a PA mixer or recording console. The signal can be derived from a point before or after effect processing. A ground lift switch is also provided, which is useful to prevent hum in the direct output caused by ground loops. Integrated auto-chromatic tuner and rhythm functions Realistic PCM sound sources are available to auto-play a number of rhythm patterns. This is convenient for use as a metronome during practice or to provide a simple rhythm part for a quick session. An autochromatic tuner for bass guitar is also built right into the unit, including a function for silent tuning which lets you easily tune your instrument on stage. Sophisticated user interface The combination of a rotary type selector and three parameter knobs make the effect editing process intuitive and quick. The mute interval when switching patches has been reduced to less than 8 milliseconds. Seamless patch changing is now a reality. Dual power supply principle allows use anywhere The B2.1u can be powered from four IEC R6 (size AA) batteries or an AC adapter. Continuous operating time on batteries is approximately 6 hours with alkaline batteries. Easy operation with expression pedal and foot switch An optional foot switch (FS01) or expression pedal (FP01/FP02) can be connected to the [CONTROL IN] jack. The foot switch is convenient for quickly toggling effect programs, setting the tempo of the rhythm function, turning delay hold on and off, etc. A connected expression pedal lets you adjust the volume in real time. Please take the time to read this manual carefully so as to get the most out of the unit and to ensure optimum performance and reliability. 4 ZOOM B2.1u Terms Used in This Manual This section explains some important terms that are used throughout the B2.1u documentation. IN COMP/LIMIT WAH/EFX DRIVE/SYNTH ZNR/MIX LO EQ HI EQ MOD/SFX DELAY REVERB OUT Effect module As shown in the illustration above, the B2.1u can be thought of as a combination of several single effects. Each of these effects is referred to as an effect module. In addition to modules comprising compressor and limiter effects (COMP/LIMIT), amp simulator/synth bass effects (DRIVE/SYNTH), and modulation/special effects (MOD/SFX), the B2.1u also provides a module for ZNR (ZOOM Noise Reduction). Various parameters such as effect intensity can be adjusted for each module individually, and modules can be switched on and off as desired. Effect type Within some effect modules, there are several different effects which are referred to as effect types. For example, the modulation/SFX effect module (MOD/SFX) comprises chorus, flanger, pitch shifter, delay, and other effect types. Only one of these can be selected at a time. Effect parameter All effect modules have various parameters that can be adjusted. These are called effect parameters. In the B2.1u, effect parameters are adjusted with the parameter knobs 1 ­ 3. Similar to the knobs on a compact effect, these change aspects such as tonal character and effect intensity. Which parameter is assigned to each knob depends on the currently selected effect module and effect type. Patch In the B2.1u, effect module combinations are stored and called up in units referred to as patches. A patch comprises information about the on/off status of each effect module, about the effect type used in each module, and about effect parameter settings. The internal memory of the B2.1u holds up to 80 patches (including 40 patches which allow read/write). Bank and area A group of ten patches is called a bank. The memory of the B2.1u comprises a total of eight banks, labelled A to d and 0 to 3. Banks A ­ d form the user area which allows read/write. Banks 0 to 3 are the preset area containing read-only patches. The patches within each bank are numbered 0 through 9. To specify a patch of the B2.1u, you use the format "A1" (patch number 1 from bank A), "06" (patch number 6 from bank 0), etc. Play mode/edit mode The internal status of the B2.1u is referred to as the operation mode. The two major modes are "play mode" in which you can select patches and use them for playing your instrument, and "edit mode" in which you can modify the effects. The module selector serves for switching between the play mode and edit mode. Operating the B2.1u on batteries 1. Turn the B2.1u over and open the cover of the battery compartment on the bottom. B2.1u bottom view Latch 2. Insert four fresh IEC R6 (size AA) batteries. Four IEC R6 (size AA) batteries 3. Close the cover of the battery compartment. Push the cover in until the latch audibly snaps into place. Insert batteries facing in alternate directions. Latch Cover Use four IEC R6 (size AA) batteries. When the batteries are getting low, the indication "bt" appears on the display. Press the latch to release it and then raise the cover. ZOOM B2.1u 5 Controls and Functions / Connections Module selector Switches between play mode and edit mode. In edit mode, the knob selects the module for operation. Top Panel BANK [-]/[+] keys In play mode, the keys serve for directly switching to the next lower or higher bank. In edit mode, the keys switch the effect type for the currently selected module. [STORE] key Serves for storing edited patches in memory. [W]/[Q] foot switches These switches are used for selecting patches, switching effect modules on and off, controlling the tuner, and other functions. Computer [USB] connector Allows you to connect the B2.1u. to a computer, for exchanging audio data. Rear Panel Mixer [BALANCED OUT] connector This XLR connector can be used to send a balanced line-level signal to PA equipment, recording devices, or similar. [PRE/POST] switch Selects the point where the signal supplied at the [BALANCED OUT] connector is obtained. In the "POST" position (switch engaged), the signal is branched at a point after effect processing, and in the "PRE" position (switch disengaged), it is branched at a point before effect processing. [GROUND] switch Determines whether the [BALANCED OUT] connector is grounded or not. In the "LIFT" position (switch engaged), the ground pin of the [BALANCED OUT] connector is uncoupled from the signal path. In the "CONNECT" position (switch disengaged), the ground pin is connected. 6 ZOOM B2.1u Controls and Functions / Connections Parameter knobs 1 - 3 These knobs allow changing the level of effect parameters or of the overall patch. During rhythm playback, the knobs let you select a pattern, set the tempo, and adjust the rhythm volume. [PEDAL ASSIGN] key This key lets you select the function of the built-in expression pedal. The currently selected function is shown by a lit LED. [TAP] key Allows manual input of time related effect parameter values such as delay time, and rhythm pattern tempo. RHYTHM [R/P] key Serves to start/stop rhythm playback. Display Shows patch numbers, setting values, and other information about operating the B2.1u. Expression pedal Lets you adjust the volume or various effect parameters in real time during play. [INPUT] jack Serves for connecting the bass guitar. Bass Guitar [DC IN] jack An AC adapter (ZOOM AD-0006) with a rated output of 9 volts DC, 300 mA (center minus plug) can be plugged into this jack. AC adapter [POWER] switch Turns the unit on and off. FP01/FP02 FS01 Headphones [CONTROL IN] jack Serves for connection of the optional foot switch (FS01) or expression pedal (FP01/FP02). [OUTPUT/PHONES] jack This stereo phone jack serves for connection to the bass guitar amplifier or for monitoring with headphones. It is also possible to use a Y cable for sending the output to two amplifiers, to produce a spacious stereo effect sound. Bass Guitar amplifiers ZOOM B2.1u 7 Selecting a Patch To try out the various effects of the B2.1u, we recommend that you simply play your instrument while switching patches. Turn power on Use a shielded cable with mono phone plug to connect the bass guitar to the [INPUT] jack of the B2.1u. When using the B2.1u with the AC adapter, plug the adapter into the outlet and plug the cable from the adapter into the [DC IN] jack on the B2.1u. Set the [POWER] switch on the rear panel of the B2.1u to ON. Turn the bass guitar amplifier on and adjust the volume to a suitable position. Set the B2.1u to play mode If the Module selector is set to a position other than "PLAY", set it to "PLAY". The bank and patch that were selected when the power was last turned off will appear on the display. A1 Bank name Patch number HINT Immediately after turning the B2.1u on, the unit will be in play mode, even if the Module selector is set to a position other than "PLAY". Select a patch To switch the patch, press one of the [W]/[Q] foot switches. Pressing the [W] foot switch calls up the next lower patch, and pressing the [Q] foot switch calls up the next higher patch. Repeatedly pressing one foot switch cycles through patches in the order A0 ­ A9 ... d0 ­ d9 00 ­ 09 ... 30 ­ 39 A0, or the reverse order. 8 ZOOM B2.1u Selecting a Patch Adjust tone and volume To adjust the effect sound and volume levels in play mode, the Parameter knobs 1 ­ 3 can be used. Each knob controls a specific parameter. Parameter knob 1 Adjusts the CABINET parameter of the DRIVE/SYNTH module (cabinet simulator effect intensity). Parameter knob 3 Adjusts the PATCH LEVEL parameter (output level of the entire patch). Parameter knob 2 Adjusts the TONE parameter of the DRIVE/SYNTH module (mainly distortion sound character). When you turn a Parameter knob, the corresponding LED lights up and the display briefly shows the current value of the respective parameter. NOTE · If the DRIVE/SYNTH module is set to OFF for the currently selected module (indication "oF" is shown on the display), Parameter knobs 1 and 2 have no effect. · The higher the setting value of Parameter knob 1 (CABINET parameter), the more will the cabinet character be emphasized. · Changes made here are temporary and will be lost when you select another patch. To retain the changes, store the patch in the user area. · The master level in common to all patches is set in edit mode ( p. 34). Directly selecting a bank To select the banks A ­ d, 0 ­ 3 directly, use the BANK [-]/[+] keys. Pressing the BANK [-] key calls up the next lower bank, and pressing the BANK [+] key calls up the next higher bank. ZOOM B2.1u 9 Using the Tuner The B2.1u incorporates an auto-chromatic tuner. To use the tuner function, the built-in effects must be bypassed (temporarily turned off) or muted (original sound and effect sound turned off). Switch to bypass or mute Setting the B2.1u to the bypass In play mode, press both [W]/[Q] foot switches together briefly and release. BP MT Setting the B2.1u to the mute state In play mode, press both [W]/[Q] foot switches together and hold for at least 1 second. Patch change at bypass/mute When you press both [W]/[Q] foot switches together while playing your instrument, the bypass/mute condition is activated. However, the sound may change momentarily just before the condition is activated. This is because the B2.1u switches to the next higher or lower patch when one of the foot switches is pressed slightly earlier. (When you cancel the bypass/mute condition, the original patch number will be active again.) This kind of behavior is not a defect. It is due to the very high speed at which the B2.1u responds to patch switching. To prevent the sound change caused by the above condition, do not produce sound with your instrument until the bypass/mute condition is fully established. Play the string to tune Play the open string to tune, and adjust the pitch. A8 The left side of the display shows the note which is closest to the current pitch. 10 ZOOM B2.1u Using the Tuner Adjusting the reference pitch of the tuner If required, you can fine-adjust the reference pitch of the B2.1u tuner. The default setting after power-on is center A = 440 Hz. Turn Parameter knob 1. The current reference pitch is shown. The adjustment range is 35 ­ 45 (center A = 435 to 445 Hz). 40 42 While the reference pitch value is shown, turn Parameter knob 1 to adjust it. When you release the Parameter knob, the display indication will return to the previous condition after a while. NOTE When you turn the B2.1u off and on again, the reference pitch setting will be reset to 40 (center A = 440 Hz). Return to play mode Press one of the [W]/[Q] foot switches. The right side of the display shows a symbol that indicates by how much the tuning is off. Pitch is high Pitch is correct Pitch is low A8 Tune other strings in the same way. Indication turns faster the more the pitch is off ZOOM B2.1u 11 Using the Rhythm Function The B2.1u has a built-in rhythm function that plays realistic drum sounds in various patterns. The rhythm function is available in play mode or in the bypass/mute condition. Set the B2.1u to play mode If the Module selector is set to a position other than "PLAY", set it to "PLAY". Start the rhythm function To start the rhythm function, press the RHYTHM [R/P] key. NOTE During rhythm playback, the REVERB module is OFF. Select a rhythm pattern The B2.1u has 40 built-in rhythm patterns. For more information on the pattern contents, see the back cover of this manual. To continuously switch rhythm patterns, turn Parameter knob 1. To select the next higher or next lower rhythm pattern, press one of the BANK [-]/[+] keys. When the above steps are carried out, the current rhythm pattern number (01 ­ 40) is briefly shown on the display. 12 ZOOM B2.1u Using the Rhythm Function Adjust the rhythm volume To adjust the rhythm volume, turn Parameter knob 3. When you turn the Parameter knob, the current setting (0 ­ 30) is shown on the display. 25 Adjust the tempo The rhythm pattern tempo can be adjusted in the range of 40 ­ 250 BPM (beats per minute). To continuously change the rhythm tempo, turn Parameter knob 2. To manually specify the rhythm tempo, hit the [TAP] key at least three times in the desired interval. At the first push of the [TAP] key, the current tempo value is shown on the display. The B2.1u then automatically detects the interval for the second and subsequent keypresses and sets the tempo accordingly. While the above steps are carried out, the current tempo value (40 ­ 250) is shown on the display. For values in the range from 100 to 199, a dot is shown after the first digit. For values of 200 and above, dots are shown after the first and second digits. 20 40 Dot is shown Dots are shown Tempo = 120 BPM Tempo =240 BPM Stop the rhythm To stop the rhythm, press the RHYTHM [R/P] key. The B2.1u returns to the previous condition. ZOOM B2.1u 13 Editing a Patch The patches of the B2.1u can be freely edited by changing the effect parameter settings. Try editing the currently selected patch to create your own sound. Select the effect module Turn the Module selector to select the effect module to edit. The following settings are available. (5) (4) (6) (3) (7) (8) (2) (9) (1) (10) (1) COMP/LIMIT module (2) WAH/EFX module (3) DRIVE/SYNTH module (4) ZNR/MIX module (5) LO EQ module (6) HI EQ module (7) MOD/SFX module (8) DELAY module (9) REVERB module (10) Pedal/foot switch related parameters When you switch to a different module, the effect type currently selected for that module is shown on the display. While the B2.1u is in edit mode, a dot appears in the bottom right of the display. Effect type AG Dot shows that unit is in edit mode To switch an effect module on and off To switch the selected module between ON and OFF, press one of the [W]/[Q] foot switches. The indication "oF" appears on the display. When you press one of the foot switches again, the indication returns to the previous condition. OF HINT The ZNR/MIX module cannot be turned off in this way. To disable ZNR, set the effect parameter value to "oF". 14 ZOOM B2.1u Editing a Patch Terminate the edit mode To terminate the edit mode and return to the play mode, set the Module selector to the "PLAY" position. NOTE When you return to play mode and select another patch, the changes you have made in edit mode will be lost unless you store the patch first. To retain the changes, store the patch as described on page 16. Change the parameter value To change the setting value of effect parameters, use the Parameter knobs 1 ­ 3. Which parameter is assigned to a knob depends on which effect module/effect type is selected. For information on parameters for effect modules/effect types, see page 27 ­ 34. When you turn a Parameter knob, the corresponding LED lights up and the display briefly shows the current value of the respective parameter. 55 NOTE When a module that is set to OFF is selected, the display will show "oF". Select the effect type To switch the effect type of the selected module, use the BANK [-]/[+] keys. SB NOTE If you press the BANK [-]/[+] keys for a module that is set to OFF, the module will be turned ON. For modules that have only one effect type, pressing the BANK [-]/[+] keys has no effect. ZOOM B2.1u 15 Storing/Copying Patches An edited patch can be stored in a bank of the user area (A ­ d). It is also possible to store an existing patch in another location to create a copy. In play mode or edit mode, press the [STORE] key The bank and patch number are shown on the display as a flashing indication. A0 NOTE Patches of banks in the preset area (0 ­ 3) are read-only. No patches can be stored or copied into these locations. If you press the [STORE] key while a patch from the preset area is selected, the patch "A0" (bank A, patch number 0) will be selected automatically as default store/copy target. Select the store/copy target bank To select the store/copy target bank, use the BANK [-]/[+] keys. D0 NOTE Only a bank of the user area (A ­ d) can be selected as store/copy target bank. 16 ZOOM B2.1u Storing/Copying Patches To cancel the store process To cancel the store process, operate the Module selector before pressing the [STORE] key again ( ). Press the [STORE] key once more When the store/copy process is completed, the B2.1u returns to the previous mode, with the target patch being selected. D4 Specify the store/copy target patch number To specify the store/copy target patch number, use the [W]/[Q] foot switches. D4 ZOOM B2.1u 17 Using the Built-in Expression Pedal The expression pedal on the top panel of the B2.1u lets you adjust the effect sound or the volume in real time during play. Which element is controlled by the pedal can be selected for each patch individually. Select the patch for which the expression pedal is to be used Select the element to be controlled by the expression pedal Press the [PEDAL ASSIGN] key to select the element to be controlled by the expression pedal. The row of LEDs above the key shows which element is currently selected. The respective selection is indicated as follows. · All LEDs are out The expression pedal has no effect. · VOLUME The expression pedal controls the volume for the entire patch. · DRIVE MIX MIX BALANCE parameter of ZNR/MIX module · WAH/EFX, MOD/SFX, DELAY, REVERB Respective module parameter HINT · Which parameter will be changed by the expression pedal depends on the effect type selected for the respective module. For details, see pages 27 - 33. · The pattern in which the parameter changes when the expression pedal is operated can be selected in edit mode from four choices. For details, see page 34. · If the module to which the expression pedal was assigned is set to OFF in the patch, the LED flashes. In this case, operating the expression pedal has no effect. If DRIVE MIX is selected, the LED flashes when the DRIVE/SYNTH module (not the ZNR/MIX module) is off. 18 ZOOM B2.1u Using the Built-in Expression Pedal Operate the pedal While playing your instrument, move the expression pedal up or down. Move up or down To switch a module on or off When you push the expression pedal fully down, the module selected with the [PEDAL ASSIGN] key is switched on or off. Push fully down Store the patch as necessary The expression pedal setting can be stored for each patch individually. NOTE If you select another patch in play mode without storing the patch, any changes that you have made to the settings will be lost. ZOOM B2.1u 19 Other Functions This section describes how to use the internal expression pedal as well as an external pedal or foot switch. Use of the B2.1u as an audio interface or direct box is also explained. sound and effect sound of the DRIVE/SYNTH module can be adjusted with the pedal. (If the DRIVE/SYNTH module is set to OFF, the pedal has no effect. ) Making settings for the internal expression pedal The built-in expression pedal on the top panel of the B2.1u can function as a volume pedal or it can be used to control an effect parameter in real time. Which function is selected for the expression pedal is stored for each patch individually. For details on parameters that can be modified with the expression pedal, see pages 27 ­ 33. MU, Md, MH, ML MOD/SFX module dU, dd, dH, dL DELAY module rU, rd, rH, rL REVERB module HINT · The modulation target can also be selected by using the [PEDAL ASSIGN] key ( p. 18). This method is available both in edit mode and in play mode. · Which parameter changes when the expression pedal is operated depends on the effect type selected for the module. For details, see pages 27 ­ 33. · The pattern in which the parameter changes when the expression pedal is operated can be selected in edit mode from four choices. For details, see page 34. 1. 2. Select the patch for which you want to use the expression pedal. Set the Module selector to the "CONTROL" position. The B2.1u goes into edit mode. 4. If necessary, store the patch. The expression pedal setting is stored as part of the patch. Select the patch in play mode and operate the expression pedal. The selected function will be activated. When the B2.1u is in the bypass condition, the expression pedal always functions as a volume pedal, regardless of the setting made in step 3. 3. Turn Parameter knob 1 to select one of the following modulation targets for the expression pedal ( p. 34). 5. oF Pedal is inactive. VL Volume WU, Wd, WH, WL WAH/EFX module bU, bd, bH, bL Adjusting the sensitivity of the built-in expression pedal The expression pedal of the B2.1u is adjusted for optimum operation at the factory, but sometimes, readjustment may be necessary. If the sound does not change when the pedal is fully pushed down, or if it changes excessively even if the pedal is only lightly pushed, adjust the pedal as follows. ZNR/MIX module NOTE When the modulation target is set to the ZNR/MIX module, the mixing balance between the original 20 ZOOM B2.1u Other Functions Turn power to the B2.1u on while keeping the [PEDAL ASSIGN] key depressed. The indication "dn" appears on the display. 1. Using an external expression pedal (FP01/ FP02) When you connect an optional expression pedal (FP01/FP02) to the [CONTROL IN] jack of the B2.1u, you can use that pedal as a volume pedal, separately from the built-in expression pedal. DN 2. With the expression pedal fully raised, press the [STORE] key. 1. Plug the cable from the external expression pedal into the [CONTROL IN] jack, and then turn the B2.1u on. Operate the external expression pedal in play mode or edit mode. The volume changes. The display indication changes to "UP". HINT The external expression pedal always functions as a volume pedal. 2. 3. Push the expression pedal fully down and then lift your foot off the pedal. Using a foot switch (FS01) Push strongly, so that pedal touches here. When foot is lifted, pedal returns slightly. Connecting an optional foot switch (FS01) to the [CONTROL IN] jack of the B2.1u allows bank switching in play mode. It is also possible to switch bypass/mute on and off, control the tap tempo function, or perform other functions with the foot switch. 1. Plug the cable from the FS01 into the [CONTROL IN] jack, and then turn the B2.1u on. Set the Module selector to the "CONTROL" position. 4. Press the [STORE] key once more. The expression pedal adjustment is completed, and the unit returns to the play mode. HINT · The point where the module is switched on or off when the pedal is depressed is always the same, regardless of the action taken in step 3. · If "Er" appears on the display, repeat the procedure from step 2. 2. The B2.1u goes into edit mode. You can now make settings for the expression pedal or foot switch. ZOOM B2.1u 21 Other Functions 3. Turn Parameter knob 2 to select one of the following functions for the foot switch. dM (delay input mute) The foot switch controls muting on/off for the delay module input signal. HINT · For information on effect parameters supporting the tap function, see pages 27 ­ 33. · To use the hold function, an effect type that supports the hold function must be selected in the patch. For details, see page 33. · While the delay module is set to hold or mute, the dot in the center of the display flashes. bP (bypass/mute) The foot switch controls bypass or mute on/off. This has the same effect as pressing both [W]/ [Q] foot switches at the same time in play mode. tP (tap tempo) Pressing the foot switch repeatedly can be used to set the interval for the rhythm function or to make settings for effect parameters supporting the tap function. This has the same effect as pressing the [TAP] key. bU (bank up) Select the patch in play mode and operate the foot switch. The selected function will be activated. This function applies to all patches. 4. Each push of the foot switch switches to the next higher bank. This has the same effect as pressing the BANK [+] key. rH (rhythm on/off) Using the B2.1u as audio interface for a computer By connecting the [USB] connector of the B2.1u to a computer, the B2.1u can be used as an audio interface with integrated AD/DA converter and effects. The operating environment conditions for this type of use are as follows. Compatible operating system · Windows XP · MacOS X (10.2 or later) Quantization The foot switch controls start/stop of the rhythm function. This has the same effect as pressing the RHYTHM [R/P] key. dH (delay hold) The foot switch controls on/off of the delay hold function. When a patch using the hold function is selected, pressing the foot switch will activate hold, causing the current delay sound to be repeated (see illustration at the bottom of this page). Pressing the foot switch once more cancels the hold condition, and the delay sound will decay normally. 16-bit quantization Original sound Delay sound Hold Foot switch pressed Pressed again 22 ZOOM B2.1u Other Functions Sampling frequency 32 kHz / 44.1 kHz / 48 kHz HINT With each of the operating systems listed above, the B2.1u will function as an audio interface simply by connecting the USB cable. There is no need to install any special driver software. audio tracks of the DAW application, mixed with the guitar sound processed by the effects of the B2.1u (see illustration at the bottom of this page). For details on recording and playback, refer to the documentation of the DAW application. NOTE · Also when using the B2.1u as an audio interface, the signal after effect processing is always available directly at the [OUTPUT/PHONES] jack. · If the DAW application has an echo back function (input signal during recording is supplied directly to an output), this must be disabled when using the B2.1u. If recording is carried out with this function enabled, the output signal will sound as if processed by a flanger effect. · Use a high-quality USB cable and keep the connection as short as possible. If power is supplied to the B2.1u via a USB cable that is more than 3 meters in length, the low voltage warning indication may appear. To use the B2.1u as an audio interface for the computer, connect the [USB] connector of the B2.1u to a USB port on the computer. The B2.1u will be recognized as an audio interface. HINT · If the [POWER] switch of the B2.1u is set to OFF, power will be supplied via the USB connection. · If the [POWER] switch of the B2.1u is set to ON, power will be supplied from the batteries in the B2.1u or the AC adapter. Care should be taken especially when running on battery power, because setting the switch to ON may result in faster depletion of the batteries. In this condition, the sound of a guitar connected to the [INPUT] jack of the B2.1u can be processed with the effects of the B2.1u and then recorded on the audio tracks of a DAW (Digital Audio Workstation) software application on the computer. At the same time, the [OUTPUT/PHONES] jack of the B2.1u carries the playback sound from the Use as a direct box The [BALANCED OUT] connector on the rear panel lets you use the B2.1u as a direct box for sending the bass signal directly to a PA mixer or recording console. (Gain: 0 dB, output impedance: 200 ohms, HOT-COLD) B2.1u [INPUT] [OUTPUT/PHONES] DAW application Effects USB [USB] Record B2.1u [INPUT] DAW application Effects USB [USB] [OUTPUT/PHONES] Playback ZOOM B2.1u 23 Restoring Factory Defaults To use this function, connect the [BALANCED OUT] connector of the B2.1u to the PA mixer or recording console, using XLR balanced cable. At the same time, you can also connect the [OUTPUT/PHONES] jack to the bass amplifier for monitoring. (The amp settings will have no effect on the signal supplied at the [BALANCED OUT] connector.) processing, select the "PRE" position (switch disengaged). [BALANCED OUT] connector B2.1u Bass guitar [OUTPUT/PHONES] jack Mixer In certain configurations, a ground loop (electrical signal loop created because devices within the same system are connected to a separate ground) may occur, leading to noise problems (audible hum). In such a case, try setting the [GROUND] switch to "LIFT". This may help to eliminate or reduce the noise. HINT Bass amp The [PRE/POST] switch lets you control the type of signal supplied at the [BALANCED OUT] connector. To use the signal after effect processing, select the "POST" position (switch engaged). To use the signal before effect The [GROUND] switch determines whether the [BALANCED OUT] connector is grounded or not. When the switch is set to the "LIFT" position (switch engaged), the ground pin of the [BALANCED OUT] connector is uncoupled from the signal path. This can be effective in eliminating or reducing hum noise caused by a ground loop. Restoring Factory Defaults In the factory default condition, the patches of the user area (A0 ­ d9) contain the same settings as the patches of the preset area (00 ­ 39). Even after overwriting the user patches, their original content can be restored in a single operation ("All Initialize" function). Turn the B2.1u on while holding down the [STORE] key. The indication "AL" appears on the display. 1. All patch settings are returned to the factory default condition, and the unit switches to play mode. To cancel All Initialize, press the RHYTHM [R/P] key instead of the [STORE] key. NOTE When you carry out All Initialize, any newly created patches that were stored in the user area will be deleted (overwritten). Perform this operation with care to prevent losing any patches that you want to keep. AL 2. To carry out the All Initialize function, press the [STORE] key once more. 24 ZOOM B2.1u Linking Effects The patches of the B2.1u consist of nine serially linked effect modules, as shown in the illustration below. You can use all effect modules together or selectively use certain modules by setting them to on or off. Effect module COMP/LIMIT COMPRESSOR LIMITER WAH/EFX AUTO WAH AUTO RESONANCE FILTER OCTAVE TREMOLO PHASER RING MODULATOR DEFRET DRIVE/SYNTH AMPEG SUPER BASS SWR ACOUSTIC BASSMAN HARTKE TRACE ELLIOT TUBE PRE SANSAMP ZNR/MIX ZNR LO EQ LO EQ LO PARAMETRIC EQ HI EQ HI EQ HI PARAMETRIC EQ MOD/SFX CHORUS STEREO CHORUS FLANGER PEDAL PITCH VIBRATO STEP DELAY TAPE ECHO PITCH SHIFTER HARMONIZED PITCH SHIFTER DELAY DELAY PINGPONGDELAY ECHO REVERB HALL ROOM SPRING Effect type PEDAL WAH TS9 ODB-3 MXR BASS D.I+ FUZZ FACE STDSYN SYNTLK MONO SYN * Manufacturer names and product names mentioned in this table are trademarks or registered trademarks of their respective owners. The names are used only to illustrate sonic characteristics and do not indicate any affiliation with ZOOM CORPORATION. For some effect modules, you can select an effect type from several possible choices. For example, the COMP/LIMIT module gives a choice between COMPRESSOR, LIMITER, and other effect types. The REVERB module comprises HALL, ROOM, and other effect types from which you can choose one. Because the ZNR/MIX module has only one effect type, you cannot choose the type for this module. HINT · The DRIVE/SYNTH module has a "CABINET" parameter that controls how the speaker cabinet characteristics are reproduced. This allows you to match the cabinet character effect to various requirements of a live performance or of direct recording. · The mixing balance of the DRIVE/SYNTH module original sound and the effect sound/synth sound, as well as the signal level after passing the module can be adjusted with the ZNR/MIX module. · When "STDSYN", "SYNTLK", or "MONO SYN" is selected as effect type for the DRIVE/SYNTH module, the action of the COMP/LIMIT module and WAH/EFX module (connection position set to "bF") will apply only to the original sound after passing the DRIVE/SYNTH module and not to the synth sound. · The ZNR/MIX module cannot be turned off with the foot switch. To disable ZNR, set the effect parameter value to "oF". ZOOM B2.1u 25 Effect Types and Parameters How to read the parameter table Effect parameters 1 ­ 3 These are the parameters that can be adjusted with Parameter knobs 1 ­ 3 when the effect type is selected. The setting range for each parameter is shown. Three-digit setting values are shown with a dot between the two numerals. Example: 1 ­ 98, 1.0 = 1 ­ 98, 100 Module selector The Module selector symbol shows the position of the knob at which this module/parameter is called up. Effect module Effect type