Operation Manual Thank you for selecting the ZOOM G1/G1X (hereafter simply called the "G1/G1X"). Please take the time to read this manual carefully to get the most out of this product and to ensure optimum performance and reliability. Keep this manual at hand for future reference. Contents SAFETY PRECAUTIONS / Usage Precautions ..................................2 Terms Used in This Manual .......... 3 Controls and Functions / Connections ................................4 Selecting a Patch ...........................6 Using the Tuner .............................8 Using the Rhythm Function ........10 Editing a Patch .............................12 Storing/Copying Patches ............14 Changing the Way Patches Are Called Up ...................................16 Using a Foot Switch or Pedal .....16 Using the foot switch (FS01) (G1 only) ............................... 16 Using the expression pedal .... 17 PATCH LEVEL ........................ 19 COMP/EFX (Compressor/EFX) module ................................. 19 DRIVE module ........................ 19 EQ module .............................. 21 ZNR/AMP (ZNR/Amp Simulator) module ................................. 21 MODULATION module ........... 22 DELAY module ....................... 23 REVERB module ..................... 24 G1/G1X Preset Pattern ............ 25 Restoring Factory Defaults ........ 25 Special Features of G1X ............. 26 [PEDAL ASSIGN] key operation ................................ 26 Adjusting the expression pedal ...................................... 26 Effect Types and Parameters .....18 Linking Effects ......................... 18 Explanation of symbols ........... 18 Specifications .............................. 27 Troubleshooting .......................... 27 © ZOOM Corporation Reproduction of this manual, in whole or in part, by any means, is prohibited. SAFETY PRECAUTIONS / Usage Precautions SAFETY PRECAUTIONS In this manual, symbols are used to highlight warnings and cautions for you to read so that accidents can be prevented. The meanings of these symbols are as follows: This symbol indicates explanations about extremely dangerous matters. If users ignore this symbol and handle the device the wrong way, serious injury or death could result. This symbol indicates explanations about dangerous matters. If users ignore this symbol and handle the device the wrong way, bodily injury and damage to the equipment could result. · High humidity or moisture · Excessive dust or sand · Excessive vibration or shock Terms Used in This Manual This section explains some important terms that are used throughout the G1/G1X documentation. Handling · Never place objects filled with liquids, such as vases, on Warning the G1/G1X since this can cause electric shock. · Do not place naked flame sources, such as lighted candles, on the G1/G1X since this can cause fire. · The G1/G1X is a precision instrument. Do not exert undue pressure on the keys and other controls. Also take Caution care not to drop the unit, and do not subject it to shock or excessive pressure. · Take care that no foreign objects (coins or pins etc.) or liquids can enter the unit. IN COMP/EFX DRIVE Effect module EQ ZNR AMP MODULATION DELAY REVERB OUT Warning Caution Please observe the following safety tips and precautions to ensure hazard-free use of the G1/G1X. Caution Connecting cables and input and output jacks You should always turn off the power to the G1/G1X and all other equipment before connecting or disconnecting any cables. Also make sure to disconnect all connection cables and the power cord before moving the G1/G1X. As shown in the illustration above, the G1/G1X can be thought of as a combination of several single effects. Each such effect is referred to as an effect module. In addition to modules such as DRIVE and MODULATION, the G1/G1X also provides a module for noise reduction and amp simulation (ZNR/AMP). Parameters such as effect intensity can be adjusted for each module individually, and modules can be switched on and off. status of each effect module, about the effect type used in each module, and about effect parameter settings. The internal memory of the G1/G1X can store up to 80 patches. Bank and area A group of ten patches is called a bank. The memory of the G1/G1X comprises a total of eight banks, labelled with letters A to d and numbers 0 to 3. Banks A ­ d are the user area which allows read/ write. 0 ­ 3 form the preset area of read-only patches. The patches within each BANK 3 PATCH 0 bank are numbered 0 BANK d BANK C 0 PATCH 1 PATCH BANK b 0 through 9. To specify a PATCH BANK A 0PATCH 1 PATCH PATCH 1 PATCH 9 PATCH 0 1 patch of the G1/G1X, you PATCH PATCH 1 PATCH 9 use the format "A1" (patch PATCH 9 PATCH9 PATCH 9 number 1 from bank A), "06" (patch number 6 from bank 0), etc. Effect type Some effect modules have several different effects which are referred to as effect types. For example, the MODULATION module comprises chorus, flanger, pitch shifter, and other effect types. Only one of these can be selected at a time. Power requirements Since power consumption of this unit is fairly high, we Warning recommend the use of an AC adapter whenever possible. When powering the unit from batteries, use only alkaline types. [AC adapter operation] · Be sure to use only an AC adapter which supplies 9 V DC, 300 mA and is equipped with a "center minus" plug (Zoom AD-0006). The use of an adapter other than the specified type may damage the unit and pose a safety hazard. · Connect the AC adapter only to an AC outlet that supplies the rated voltage required by the adapter. · When disconnecting the AC adapter from the AC outlet, always grasp the adapter itself and do not pull at the cable. · During lightning or when not using the unit for an extended period, disconnect the AC adapter from the AC outlet. Alterations Warning Never open the case of the G1/G1X or attempt to modify the product in any way since this can result in damage to the unit. Volume Caution Effect parameter All effect modules have various parameters that can be adjusted. These are called effect parameters. When thinking of an effect module as a compact effect, the parameters change the tone and effect intensity similar to the knobs on the device. Do not use the G1/G1X at a loud volume for a long time since this can cause hearing impairment. Mode The internal status of the G1/G1X is referred to as the operation mode. In "play mode" you can select patches and use them for playing your instrument. In "edit mode" you can modify the effects, and there is also a "rhythm mode" in which you can make settings for the rhythm function. The module selector serves for switching between these three modes. Usage Precautions Electrical interference For safety considerations, the G1/G1X has been designed to provide maximum protection against the emission of electromagnetic radiation from inside the device, and protection from external interference. However, equipment that is very susceptible to interference or that emits powerful electromagnetic waves should not be placed near the G1/G1X, as the possibility of interference cannot be ruled out entirely. With any type of digital control device, the G1/G1X included, electromagnetic interference can cause malfunctioning and can corrupt or destroy data. Care should be taken to minimize the risk of damage. Patch In the G1/G1X, effect module combinations are stored and called up in units referred to as patches. A patch comprises information about the on/off [Battery operation] · Use four conventional IEC R6 (size AA) batteries (alkaline). · The G1/G1X cannot be used for recharging. · Pay close attention to the labelling of the battery to make sure you choose the correct type. · When not using the unit for an extended period, remove the batteries from the unit. · If battery leakage has occurred, wipe the battery compartment and the battery terminals carefully to remove all remnants of battery fluid. · While using the unit, the battery compartment cover should be closed. Operating the G1/G1X on batteries 1. Turn the G1/G1X over and open the cover 2. Insert four fresh IEC R6 3. Close the cover of the of the battery compartment on the bottom. G1/G1X bottom view Cover Four IEC R6 (size AA) batteries (size AA) batteries. Polarity is opposite for two banks of two batteries each. battery compartment. Push the cover in until the latch audibly snaps into place. Cleaning Use a soft, dry cloth to clean the G1/G1X. If necessary, slightly moisten the cloth. Do not use abrasive cleanser, wax, or solvents (such as paint thinner or cleaning alcohol), since these may dull the finish or damage the surface. Use four IEC R6 (size AA) batteries When the batteries are getting low, the indication "bt" appears on the display. When operating the G1/G1X on batteries, it is advisable to disconnect the guitar cable plug from the [INPUT] jack when not using the unit, to conserve battery power. Environment Warning To prevent the risk of fire, electric shock or malfunction, avoid using your G1/G1X in environments where it will be exposed to: · Extreme temperatures · Heat sources such as radiators or stoves Latch Please keep this manual in a convenient place for future reference. Press latch to release and then lift the cover. 2 ZOOM G1/G1X ZOOM G1/G1X 3 Controls and Functions / Connections Controls and Functions / Connections [VALUE] knob This section describes the names and functions of all parts of the G1 and G1X. Functions that are special to the G1X are explained on page 26. Please also refer to that section. This knob allows changing the level of effect parameters or of the overall patch. Module selector Switches between play mode, edit mode, and rhythm mode. In edit mode, the knob selects the module for operation. Top Panel (G1X) Expression pedal (G1X only) Can be used as a volume pedal or as a real-time controller for effect parameters. (For details, see page 26.) [STORE] key Serves for storing edited patches in memory. RHYTHM [R/P] key In play mode and rhythm mode, this key serves to start and stop the rhythm pattern. In edit mode, the key serves to select the module to control with the pedal. [PEDAL ASSIGN] key (G1X only) Serves to select the module to assign to the built-in expression pedal. Display Shows patch numbers, setting values, and other information for operating the G1/G1X. When operating the G1/G1X on batteries, it is advisable to disconnect the guitar cable plug from the [INPUT] jack when not using the unit, to conserve battery power. [BANK UP·TAP] key In play mode, the key switches to the next higher bank. In other modes, the key lets you manually specify the rhythm pattern tempo and other parameters related to timing and cycle. [W]/[Q] foot switches These switches are used for selecting patches, controlling the tuner, and other functions. Guitar Rear Panel (G1) AC adapter Differences between G1X and G1 G1X special features that differ from G1: · Equipped with expression pedal as standard feature ( p. 26) · [PEDAL ASSIGN] key on top panel allows selection of module to be controlled with expression pedal ( p. 26) · No [CONTROL IN] jack on rear panel; optional foot switch (FS01) or expression pedal (FP01/FP02) cannot be used. [INPUT] jack Serves for connecting the guitar. When operating the G1/G1X on batteries, inserting the guitar cable plug into this jack will turn the unit on. [OUTPUT/PHONES] jack This stereo phone jack serves for connection to the guitar amplifier. It is also possible to use a Y cable for sending the output to two amplifiers, or to plug a pair of stereo headphones into this jack. Headphones [DC IN] jack An AC adapter (ZOOM AD-0006) with a rated output of 9 volts DC, 300 mA (center minus plug) can be plugged into this jack. [CONTROL IN] jack (G1 only) FS01 Guitar amplifiers FP01/FP02 Serves for connection of the optional foot switch (FS01) or expression pedal (FP01/FP02). 4 ZOOM G1/G1X ZOOM G1/G1X 5 Selecting a Patch Selecting a Patch To try out the various effects of the G1/G1X, we recommend that you simply play your instrument while switching patches. Turn power on When using the G1/G1X on batteries, plug a shielded cable with mono phone plug into the [INPUT] jack on the rear panel of the G1/G1X. When using the G1/G1X with the AC adapter, plug the adapter into the outlet and plug the cable from the adapter into the [DC IN] jack on the G1/G1X. Turn the guitar amplifier on and adjust the volume to a suitable position. Adjust the master level To adjust the master level in play mode, you can use the [VALUE] knob. When you turn the [VALUE] knob, the master level setting is shown for a time on the display. 80 The master level setting range is 0 ­ 98, 1.0. It will be reset to 80 when the unit is turned off and then on again. Set the G1/G1X to play mode If the Module selector is set to a position other than "P ...